Manual Trumatic Ultraheat (page 6 of 28) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish)

484606

Zoom out

Zoom in

1/28

Push sealing plate (8) about 3 cm onto the exhaust duct (claw

must point to the sleeve on the heater). Insert thrust collar (17).

Replace O-ring (16) with the enclosed O-ring.

The enclosed 53 x 5 mm O-Ring may only be

used with heaters from model 01/88 onwards.

The 35 x 5 mm O-ring (part no. 10030-25000) must

be used for older heaters. In this case consult your

specialist dealer!

Stretch O-ring (16) and carefully insert over the cut end of

the duct and push the exhaust duct in t o the sleeve as far as it

will go.

Push the O-ring, the thrust collar and the sealing plate up to

the sleeve. Attach sealing plate (8) by turning and tighten with

screw (9).

Fig. B

Screw gas supply line (7) back on beneath the vehicle.

Affix the enclosed nameplate to the inside of the heater cover.

Reattach heating cover.

Installation of the control panel

When using operating elements which are specific to

the vehicle or the manufacturer, the electrical connec-

tion must be established in accordance with the Truma inter-

face descriptions. Any modification made to the Truma com-

ponents pertaining to this will lead to the invalidation of the

guarantee, as well as to the exclusion of any claims for liability.

The installer (manufacturer) is responsible for providing in-

structions for use for the user as well as for identification

printing on the control panels!

In selecting a location, make sure that neither the front nor the

back of the control panel will be exposed to direct heat.

Length of connection cable 3 m. If required, a cable extension

of 5 m in length is available (which in combination can be

extended to 8 m – part no. 34300-01).

If the control panel can only be installed behind curtains or

similar location where temperature fluctuations may occur, it

is necessary to use a remote sensor for the room temperature

(part no. 34201-01).

If the control panels cannot be flush-mounted, Truma

can provide an on-surface frame (18), part no. 40000-

52600, as an accessory.

Fig. G

Drill a hole 55 mm in diameter.

Plug the operating cable (19) into the control panel (20) and fit

on the rear cover cap (21) as a strain-relieving device.

Feed the cable through to the back, secure the control panel

with four screws (22) and fit the cover frame (23).

Truma offers side parts (24) in eight different colors for

finishing the cover frames in a visually pleasing way.

Please ask your dealer.

Route the control panel cable (19) to the appliance and

connect to the control electronics.

For strain relief, secure control panel cable (19) on the control

electronics by means of enclosed cleat (25).

Depending on the method of installation, the control

panel cable may be installed in the reverse direction, i.e.

connected first to the control electronics and secured by

means of the cleat. Then feed through to the control panel

and connect it to the latter.

230 V Electrical supply

The 230 V electrical connection must always be made

by an expert (in accordance with VDE 0100, part 721 or

IEC 60364-7-721, for example, in Germany). The instructions

provided here should not be understood as a recommendation

for amateurs to install the electrical supply line. They are in-

tended as additional information for the professional electri-

cian you have hired!

Connect to the mains supply via the 150 cm long silicone

cable by means of a fuse-protected line of at least 10 A (better

16 A).

Be sure to connect the wires according to the correct colours!

For maintenance and repair work a separator must be provid-

ed for all-pole separa-tion from the mains supply with at least

3.5 mm contact clearance.

Function test

Before operating for the first time, the appliance, ex-

haust ducting and gas-tightness of the whole installa-

tion (by the pressure drop method) must be checked by

an expert.

In order to avoid damage to the electronics, make sure that

the hot air hoses on the Trumavent fan are attached securely

and fastened with a screw.

Finally, test all functions of the appliance in accordance with

the operating instructions.

The operating instructions must be handed to the owner of

the vehicle.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Trumatic Ultraheat in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trumatic Ultraheat

Trumatic Ultraheat User Manual - English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Trumatic Ultraheat Manual

Product: