Manual Trumatic Hoogteset Combi D (page 5 of 24) (English, German, Dutch, Danish, French, Italian, Spanish)

484621

Zoom out

Zoom in

1/24

Intended use

The altitude kit is required if the heating mode of the Combi D

is run for longer periods at heights of 1500 m to 2750 m.

Operating instructions

Working the changeover switch

Select the required switch setting before switching the heater on.

– Setting 1 = Normal mode up to 1500 m

– Setting 2 = Altitudes from 1500 m to 2750 m

The right to effect technical modifications is reserved!

Installation instructions

We recommend having the installation performed by a

qualified mechanic.

Observe applicable national regulations concerning the

handling of diesel fuel. Wear appropriate personal pro-

tection (e.g. suitable protective gloves). Avoid the build-up of

static charges, remove any ignition sources from the vicinity

and do not smoke. Ensure a good level of ventilation. Discon-

nect the battery before commencing work. Collect any escap-

ing diesel fuel in an appropriate vessel.

Scope of supply kit

1 Cable harness

1 Dosing pump (adjusted to high altitude)

1 Support

1 Angle

1 Set of connection parts

– 1 Y-piece Ø 4 mm

– 1 Y-piece Ø 5 mm

– 4 Reducer part 5 x 3.5 mm

– Clamps Ø 10 mm

1 Fuel line 2 m, 4 x 1 mm

1 Fuel hose 0.5 m, 3.5 x 3 mm

1 Changeover switch with cover

– 1 Shrink hose

– 3 Tab receptacles

1 Plug connector housing

1 Operating instructions / Installation instructions

Altitude kit

Fuel connection

Safety instructions for routing fuel lines

Always cut fuel hoses and lines to length using a hose cutter

(part no. 34020-45100) or other sharp knife. The areas that

have been cut must not be compressed and must be free of

burrs.

Fuel lines must always slope upwards when they are routed

from the metering pump to the heater (as uniformly as possible).

Fuel lines must be securely attached in order to prevent

damage and / or noise generation caused by vibration (recom-

mended spacing between attachment points approx. 50 cm).

Fuel lines must be protected from mechanical damage.

Route fuel lines so that vehicle twisting, engine movements

and the like do not adversely affect the stability thereof.

Protect fuel-carrying parts from heat that may affect operation

(use suitable thermal protection hose made from fibre glass

fabric with aluminium lining).

Never route or secure fuel lines immediately adjacent to the

exhaust ducts of the heater unit or the vehicle engine. If the

lines cross, maintain an adequate distance away from hot

components at all times – provide heat radiation protection

plates if necessary.

Do not leave gaps between fuel lines that are being connected

using a fuel hose. This prevents problematic bubble formation.

Correct line routing

Erroneous line routing

(bubble formation)

Installing the metering pump

Install the dosing pump (adjusted to high altitudes) in the fuel

system parallel to the standard dosing pump.

Always install metering pump with the pressure side (delivery

direction) sloping upwards.

Protect metering pump from heat (max. operating tempera-

ture 40 °C), therefore do not install in the vicinity of sound

mufflers and exhaust pipes.

Metering pump installation position

0˚

15˚

35˚

90˚

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Trumatic Hoogteset Combi D in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 2,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Trumatic Hoogteset Combi D Manual

Product: