Manual Trumatic E 2400 (page 22 of 88) (English, German, Dutch, Danish, French, Italian, Spanish)

484023

Zoom out

Zoom in

1/88

Cowls must always be fitted to prevent any waste gases en-

tering the inside of the vehicle. The waste gas must always be

guided to at least a side wall.

The wall cowl must be at-

tached so that no tank sup-

ports or tank ventilation

openings are found within

500 mm (R). In addition, no

air discharge apertures for the

living area or window open-

ings may be located with

300 mm (R) of it.

When fitting the cowl

within the marked area

below or next to a window

that must be open, an

electrical window switch

(part no. 34000-85800) must

be installed. The gas unit must

automatically switch itself off

using the Truma automatic

shut-off facility if the window

is opened (Accessories,

part no. 39050-00800).

300 mm

Exhaust duct

With the Trumatic E 2400 only use the Truma exhaust duct

AA 24 (part no. 39420-00) for the installation with wall cowl,

and for boats use the Truma stainless steel exhaust duct

AEM 24 (part no. 39430-00) and the combustion air supply

duct ZR 24 (part no. 39440-00) as the appliance has only been

tested and approved with these ducts.

A new O-ring must always be installed after dismantling

the exhaust duct!

Permissible duct lengths

1. Interior installation with wall cowl

(refer to installation variant 1, page 2):

– Duct lengths of up to max. 70 cm can be routed as

ascending duct in any way required, or descending by

max. 30 cm.

– Duct lengths from 70 cm to max. 150 cm must be

routed as ascending duct with an ascending angle of

min. 45°.

2. Under-floor assembly with wall cowl

(refer to installation variant 2, page 2):

– Cowl double duct length max. 70 cm, routed as

ascending duct in any way required or descending by up

to 30 cm.

Interior installation using the wall cowl kit

Refer to installation variant, Fig 1 (page 2).

Assembly of wall cowl

Assemble wall cowl on a surface which is as flat as possible

and which is exposed to wind from all directions. Drill an

opening (8) measuring 70 mm in diameter (pack wood into

hollow spaces in the area of the cowl opening). Use the pro-

vided rubber seal (10) for sealing. In the event of structured

surfaces, coat with plastic body sealant – do not use silicone.

In the event of a greater wall thickness, first connect the

exhaust double duct to the cowl from the outside.

Slide rubber seal (10) and clamp (4) onto the cowl inner

part (11).

Press end of ex-haust duct (1) together so that winding

touches winding, slide over the O-ring (2a) on the connection

fitting (2) up to the collar (3 – cowl bend pointing upward) and

tighten clamp (4) in such a way that the knurled edge of the

clamp encloses the collar.

32a

Coat serrated connection fitting (9) with plastic body seal-

ant – do not use silicone! – and slide over combustion air sup-

ply duct (5).

Fasten cowl inner part (11) with 3 screws (12 – observe instal-

lation position! The Truma lettering must be at the bottom).

Mount cowl outer part (13) and screw on with 2 screws (14).

Always install a new O-ring following any disassembly!

Fastening the appliance

Depending on the installation position, bolt on the appliance

using fastening strap (a) or mounting brackets (b). Fasten

exhaust double duct to the wall using duct clamp ZR 24 (c), if

necessary (parts to be found in enclosed kit).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Trumatic E 2400 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 2,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Trumatic E 2400 Manual

Product: