484625
18
Zoom out
Zoom in
Previous page
1/24
Next page
18
Exhaust duct
With the Trumatic E 2400 E only use the Truma exhaust duct
AA 24 (part no. 39420-00) for the installation with wall cowl
and the combustion air supply duct ZR 24 (part no. 39440-
00) as the appliance has only been tested and approved with
these ducts.
A new O-ring must always be installed after disman-
tling the exhaust duct!
Permissible duct lengths
1. Interior installation with wall cowl (refer to installation
variant 1, page 2):
Duct lengths of up to max. 70 cm can be routed as as-
cending duct in any way required, or descending by max.
30 cm.
Duct lengths from 70 cm to max. 150 cm must be rout-
ed as ascending duct with an ascending angle of min. 45°.
2. Under-floor assembly with wall cowl (refer to installation
variant 2, page 2):
Cowl double duct length max. 70 cm, routed as ascend-
ing duct in any way required or descending by up to 30 cm.
Interior installation using the wall cowl kit
Refer to installation variant, Fig 1 (page 2).
Assembly of wall cowl
Assemble wall cowl on a surface which is as flat as possible
and which is exposed to wind from all directions. Drill an
opening (8) measuring 70 mm in diameter (pack wood into
hollow spaces in the area of the cowl opening). Use the pro-
vided rubber seal (10) for sealing. In the event of structured
surfaces, coat with plastic body sealant – do not use silicone.
In the event of a greater wall thickness, first connect the
exhaust double duct to the cowl from the outside.
Slide rubber seal (10) and clamp (4) onto the cowl inner part (11).
Coat serrated connection fitting (9) with plastic body sealant
– do not use silicone! – and slide over combustion air supply
duct (5).
1
4
2
3
2a
Press end of ex-haust duct (1) together so that winding
touches winding, slide over the O-ring (2a) on the connection
fitting (2) up to the collar (3 – cowl bend pointing upward) and
tighten clamp (4) in such a way that the knurled edge of the
clamp encloses the collar.
Fasten cowl inner part (11) with 3 screws (12 – observe instal-
lation position! The Truma lettering must be at the bottom).
Mount cowl outer part (13) and screw on with 2 screws (14).
Always install a new O-ring following any disassembly!
Fastening the appliance
Depending on the installation position, bolt on the appliance
using fastening strap (a) or mounting brackets (b).
Fasten exhaust double duct to the wall using duct clamp
ZR 24 (c), if necessary (parts to be found in enclosed kit).
Double cowl duct connection to the
heating appliance
Press end of ex haust duct (1) together so that winding touch-
es winding. Slide clamp (4) over exhaust duct (1). Slide ex-
haust duct over O-ring on the connection fitting (2) up to the
collar (3). Attach with clamp (4) in such a way that the knurled
edge of the clamp encloses the collar. Fasten combustion air
supply duct (5) on the connection fitting (6) using clamp (7).
Always install a new O-ring following any dis-assembly!
Under-floor assembly with wall cowl kit
Refer to installation variant fig. 2 (page 2).
Install wall cowl on as flat a surface as possible on an outside
wall (vehicle apron, refer to “Interior installation using the wall
cowl kit”).
If the wall cowl is fitted with fixing brackets or similar
below the floor, the vehicle floor must be airtight and
the waste gas must always be guided up to the side wall (see
„Choosing the installation place“).
Fastening the appliance
Screw the 3 fastening strips (1, 2 + 3) to the appli-ance. Screw
appliance to vehicle floor with the strips 1 + 2. Fasten assem-
bly bracket (4 – special equipment Part. no. 39050-74000) to-
gether with strip (3) and screws (5). Place lock washers under
all screw heads and nuts.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trumatic E 2400 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trumatic E 2400 E in the language / languages: English, German as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trumatic E 2400 E

Trumatic E 2400 E User Manual - English, German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info