629581
10
Zoom out
Zoom in
Previous page
1/30
Next page
7
or for Percentage Mode
To change the cylinder size
with the device switched on,
press button „B“ and keep it
pressed until the desired
cylinder size or Percentage
Mode appear in the display.
The measuring time starts af-
ter further 2 seconds. The gas
cylinder content can then be
read off from the display:
For example, for 11 kg con-
tents (gas cylinder full)
or for residual content 2.5 kg
(11 kg gas cylinder only
about 1/4 still filled)
kg
kg
%
The display will switch off
automatically after about
10 seconds.
2
Filling level
as percentage
In Percentage Mode, it is
possible to measure the con-
tents of almost all conven-
tional commercial propane or
butane gas cylinders with fill-
ing weights of up to about
15 kg (which fit on the cylin-
der mount).
By contrast with the standard
measurement in kg, because
of the different cylinder sizes
it is not possible to make re-
course to preset values.
Accordingly, before starting
operation, a basic value of
100 % must be stored in the
memory for the gas cylinder
which is to be measured.
This is done as a rule with the
cylinder completely filled
(filled with butane or propane
depending on the design).
Place the full gas cylinder on
the cylinder mount (make
sure the contact surfaces
are clean!) and secure it as
specified.
Note: To determine a basic
value (100 %), the cylinder
concerned must be more
than half filled, as otherwise
the contents cannot be deter-
mined, and the display will
show:
Percentage
Measurement
To switch the device on, press
button „A“ once, briefly.
The device will carry out a
brief self-test. The measuring
mode set at that particular
time will then be displayed.
The measuring mode can be
changed as appropriate by
pressing button „B“ and kee-
ping it pressed down until the
Percentage display shows:
%
flashing
After a further 2 seconds, the
device will start carrying out
the basic measurement, and
the contents of the gas cylin-
der at that particular moment
will be shown on the display,
flashing, as 100 %.
Now confirm this value
(100 % flashing) by pressing
buttons „A“ and „B“ simulta-
neously, until the display
stops flashing (about
2 seconds).
The device will then carry out
another short measurement,
and the display will show:
After some gas has been
withdrawn, Sonatic will then
show the cylinder content at
%
%
flashing
%
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Sonatic at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Sonatic in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info