Manual Truma Saphir Vario (page 13 of 68) (English, German, Dutch, Danish, French, Italian, Spanish)

489374

Zoom out

Zoom in

1/68

Before starting to use the device, it is essential that the

Operating Instructions and “Safety instructions” be read

carefully! The vehicle owner is responsible for ensuring that

the device can be operated in the proper manner.

Remote control

+/– = Setting

FAN

Hr.

COOL

MODE

FAN

MODE

COOL LOW

TEMP.

TIMER

COOL HIGH

COOL

FAN LOW

FAN HIGH

°C

TEMP.

MODE

TIMER RESEND

ON / OFF

Saphir vario

Operating level,

Timer, Temperature

a = MODE

Operating mode

selector switch

FAN = Ventilation only

COOL = Cooling and

ventilation

b = FAN

Blowing power

LOW = Low

HIGH = High

c = TEMP.

Desired interior

temperature

16 °C to 31 °C

d = No function

e = TIMER off

Set timer to 1 to 15 hours

f = RESEND

Send the settings of the remote control to device

again

g = ON / OFF

On / Off switch

Taking into operation

Before switching on, it is essential to make sure that the fuse

system for the power supply at the camp site is sufficient

(230 V):

600 W / 1.7 A

1500 W / 3.0 A

2000 W / 4.4 A

In order to prevent the power cable for the caravan from

overheating (minimum cross-section 3 x 2.5 mm²) the

cable drum must be fully unwound.

To carry out the individual switching commands, the remote

control must always be pointed at the infra-red receiver.

1. Switch the Saphir vario on using button “g” on the remote

handset. The “COOL MODE” that was previously selected

using the remote handset is automatically used.

2. Set the desired operating mode using the button “a”.

FAN: Ventilation only (without cooling).

COOL: Cooling with 3 levels.

The blowing power and the interior temperature can be ad-

justed individually. The green indicator lamps on the receiver

indicate compressor operation and therefore cooling operation

with three levels.

600 W = LED 1 (COOL LOW),

1500 W = LED 2 (COOL),

2000 W = LED 1 + LED 2 (COOL HIGH)

Operating instructions

3. If necessary, adjust the fan speed and the room tempera-

ture to the required settings using buttons “b”, “c”, “+”,

and “–”.

When the room temperature that was selected using the

remote handset is reached in cooling mode, the compressor

switches off and the green indicator lamps in the receiver go

out. The circulation fan continues to run in order to provide

ventilation. If the room temperature is exceeded the device

automatically reverts to cooling mode.

Switching off

To switch off, press the button “g” on the remote control

once again.

If the air conditioning unit is switched on again within

approximately 3 minutes, the green indicator lamp blinks.

The air circulation fan runs, and the compressor activates itself

after 3 minutes.

Timer off

The air conditioning unit deactivation time can be set up to

15 hours in advance using the integrated timer, starting from

the current time.

To carry out programming, first switch the device to remote

control mode with the switch “g”.

Then set the operating mode and the room temperature using

buttons “a”, “b”, “c”, “+”, and “–”.

Then select the required deactivation time (1 – 15 hours) using

the “e” button (TIMER).

The programming is not active unless the air condi-

tioning unit is switched on. The remote handset can be

deactivated by covering the infrared transmitter on the front

of the remote handset. This prevents unintentional air con-

ditioning unit deactivation and accidental deactivation time

reprogramming.

IR receiver and manual on / off

There is an additional pushbutton on the receiver (m), with

which the unit can also be switched on and off without the

remote control (e.g. with a ballpoint pen).

LED 1

LED 3

LED 2

Saphir vario

If the unit is switched on using

this pushbutton, the system is

automatically reset to the fac-

tory settings (COOL, FAN HIGH,

TEMP. 21 °C).

Operating indicator

LED 1 green (600 W)

LED 2 green (1500 W)

LED 1 and LED 2 (2000 W)

LED 3 red – flashing – (data is being transmitted)

LED 3 red – permanently on – (fault)

Red LED illuminates

The unit is indicating a fault. Switch unit off, wait for a short

time and switch on again. If the red LED continues to illumi-

nate, please contact Truma Service.

Hi there was one of these installed when we bought the van but it doesn't blow ice cold air? what could be wrong?? Submitted on 26-2-2023 at 14:25
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Truma Saphir Vario in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 10,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Truma Saphir Vario Manual

Product: