590215

Truma Mover XT2 Manual

22
Zoom out
Zoom in
Previous page
1/96
Next page
22
Read the installation instructions carefully before commenc-
ing the work, and then comply with them.
Please ensure that no metal chips or other contaminants get
into the control unit during installation.
In the case of screws with sealant, make sure that the
thread is free of grease / oil.
Intended use
The Mover® XT was designed for use on single-axle
caravans with a gross weight of up to 2300 kg.
The Mover® XT2 was designed for use on dual-axle
caravans with a gross weight of up to 2400 kg.
The Mover®XT / XT2 weighs approx. 28 kg.
Check the maximum towable weight for your towing
vehicle and the gross weight of your caravan to make
sure that they are designed for this additional weight.
Approval
The Truma Mover®XT / XT2 has design approval, and a “gen-
eral operating permit” (ABE) has been issued for Germany.
Acceptance by a vehicle expert is not required (except when
installing the low chassis kit). The general operating permit
(ABE) must be kept in the vehicle.
The Mover®XT / XT2 complies with other requirements of
EC Directives and Standards (see Declaration of conformity).
When installing the Mover®XT / XT2, the technical and ad-
ministrative regulations of the country of first registration of
the vehicle must be observed.
Any modifications made to the device, or the use of any spare
parts or functionally significant accessories other than original
Truma parts, or failure to comply with the contents of the op-
erating and installation instructions invalidates the warranty
and precludes any liability claims. This will also invalidate the
operating permit for the equipment.
Tools and facilities required
To install the Mover®XT / XT2 you need:
– 8mm, 10mm,13 mm and 17 mm socket wrenches, ring
spanners or open-jawed spanners
– Allen key 4
– Torque wrenches (3.5 – 50 Nm)
– Cable cutter / crimping tool
– Electric drill / screwdriver / keyhole saw, diameter 25 mm
– 2-tonne trolley jack and suitable support trestles
– Adequate lighting
Minimum installation dimensions
A distinction is made between L-profile and U-profile
frames as shown in the illustration.
Caravan floor
L-profile
U-profile
max. 20
Figure 6
Installation is only possible on caravans / trailers with the fol-
lowing dimensions.
min.
170*
min. 1350 / max. 2000
min. 80 / max. 180
min. 25
min. 35 **
140
min. 2.8
Caravan floor
Figure 7
All dimensions in mm.
* with loaded vehicle with max. permissible gross weight
** with U-profile
Measuring the frame height
A frame height of at least 140 mm is required at the level of
the tyre hub / tyre centre in the range of 320 mm from the
outer edge of the tyre.
min. 320
min. 140
Figure 8
Determining the installation type
1. Standard installation
Standard installation is used with a U-profile or L-profile
chassis and a frame height of at least 140 mm. No special
accessories are required.
2. Installation on chassis with U-profile or L-profile and a
frame height of between 80 mm and less than 140 mm
In order to compensate for height, the 30mm spacer set (for
frame heights down to 110mm) or the 60mm spacer set
(for frame heights of less than 110mm down to 80mm) is
required.
3. Installation on chassis with U-profiles or L-profiles
with a frame height of less than 80 mm
If the chassis has a frame height of less than 80mm, a low
chassis kit must be fitted to compensate for the height.
If a low chassis kit is used in Germany, accept-
ance by a vehicle expert is required.
4. For the AL-KO Vario III / AV chassis with a frame thickness
of less than 2.8 mm it is essential to use the AL-KO
VarioIII / AV installation kit as a reinforcement.
5. For attachment in front of the axle on the AL-KO
chassis M with adjustable beams
The AL-KO chassis M adapter set (part no. 60030-38600)
must be used in order to compensate for overlapping frame
edges.
6. For attachment in front of the axle on the AL-KO
chassis M with continuous frame
The AL-KO chassis M adapter set (part no. 60031-02000)
must be used in order to compensate for overlapping frame
edges.
7. Installation on the Eriba Touring chassis
It is essential to use the Eriba Touring mounting set for the
Eriba Touring chassis.
8. Installation on chassis with L-profile and with a lim-
ited amount of space
The short mounting system is required to compensate for
the height (30 or 60 mm) with substructures such as tanks.
Installation instructions
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Mover XT2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover XT2 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 11,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info