Manual Truma Mover XT (page 21 of 96) (English, German, Dutch, Danish, French, Italian, Swedish)

590214

Zoom out

Zoom in

1/96

Declaration of conformity

1. Information about the manufacturer

Name: Truma Gerätetechnik GmbH & Co. KG

Address: Wernher-von-Braun-Str. 12, D-85640 Putzbrunn

2. Device identification

Type / model:

Mover®XT / XT2 manoeuvring assistant

3. Complies with the requirements of the following

ECdirectives

3.1 R&TTE Directive 1999/5/EC

3.2 Radio interference suppression of motor vehicles

UN ECE R10

3.3 Low Voltage Directive 2006/95/EC

3.4 End-of-life vehicle directive 2000/53/EC

and bears the type approval number E1 10R-046968

and the CE mark.

Mover®XT / XT2

Class 2, frequency 868 MHz.

Countries:

AT, BE, BG, CH, CY, CZ, DE, DK, EE, ES, FI, FR, GB, GR, HU,

IE, IS, IT, LT, LU, LV, MT, NL, NO, PL, PT, RO, SE, SI, SK.

4. Basis of the proof of conformity

ETSI EN 300220-2; ETSI EN 300220-1;

ETSI EN 301 489-3; IEC 60950-1:2005 (2nd Edition);

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011

5. Monitoring body

Federal Motor Transport Authority (Kraftfahrt-Bundesamt)

6. Signatory details

Signature: p.p. Axel Schulz

Product Centre Manager Putzbrunn, 14.05.2013

Truma Manufacturer's Warranty

1. Warranty claims

The Manufacturer hereby warrants for all defects of the unit

caused by material or production faults. In addition, the seller

continues to be subject to any statutory warranty claims.

No warranty claim shall be applicable under the following

circumstances:

– Consumable parts which are subject to wear and tear

– Use of parts other than original Truma components in any

of the units

– In gas pressure regulation systems: damage caused by

foreign substances in the gas (e.g. oils, plasticisers)

– Failure to observe Truma's installation or operating

instructions

– Improper handling

– Improper transport packing

2. Scope of warranty

The warranty covers all defects under clause 1 that occur

within 24 months upon concluding the purchase agreement

between the seller and the end customer. The Manufacturer

undertakes to remedy such defects through subsequent fulfil-

ment, i.e. at its discretion either by repairing or replacing the

defective item. If the Manufacturer remedies a defect under

its warranty commitment, the term of the Warranty shall not

recommence anew with regard to the repaired or replaced

parts; rather, the original warranty period shall continue to be

applicable. No further-reaching claims shall be permitted, es-

pecially damage claims presented by purchasers or third par-

ties. This provision shall not affect the validity of the German

Product Liability Act (Produkthaftungsgesetz).

The Manufacturer shall bear the cost of employing the Truma

Customer Service for the removal of warranty defects – in

particular, transportation, travelling, job and material costs –

provided that the Customer Service conducts its work within

Germany. This Warranty does not cover Customer Service

work outside Germany.

Additional costs arising from complicated removal or instal-

lation jobs on the unit (e.g. dismantling of furnishings or parts

of the vehicle body) are not covered by the Warranty.

3. Making a claim under the warranty

The Manufacturer‘s address is:

Truma Gerätetechnik GmbH & Co. KG

Wernher-von-Braun-Straße 12

85640 Putzbrunn, Germany

Should problems occur, please contact the Truma Service

Centre or one of our authorised service partners (see

www.truma.com). Please describe your claim in detail and

state the serial number of the unit and the date of purchase.

To help the Manufacturer determine whether your claim is

covered by the Warranty, the end user must take or send the

unit to the Manufacturer or service partner at their own risk.

In the event of damage to the heat exchanger, the gas pres-

sure regulator, too, must be returned along with the unit.

Air conditioning systems:

To avoid transport damage, the unit must be sent either to the

Truma Service Centre in Germany or to the relevant author-

ised service partner; this must only be done upon prior arrange-

ment. Otherwise the sender shall bear the risk for any transport

damage that may occur.

If a unit is sent to the manufacturing facility, make sure it

is shipped as a freight item. If the claim is covered by the

Warranty, transport / shipping and the cost of return shall

be borne by the manufacturing facility. If the claim is not

covered by the Warranty, the Manufacturer shall notify the

customer to this effect, specifying the cost of repairs not

borne by the Manufacturer; shipping costs, too, shall be

borne by the customer in such a case.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover XT in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 11,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Truma Mover XT Manual

Product: