Manual Truma Mover XT 4 (page 26 of 88) (English, German, Dutch, Danish, French, Italian, Swedish)

590216

Zoom out

Zoom in

1/88

Connecting the safety socket

Lead the supplied 2-wire cable (10m) with the flat connectors

through the socket holder (g) and the rubber sleeve (h).

If necessary, open cover and push socket connection out of

socket housing (i).

Connect 2-wire cable with flat connectors to micro switch.

RD / BK

Figure 29

If necessary, insert socket connector back into socket housing (i).

Screw socket housing (i) with rubber seal (h) to socket holder

(g) using 3 sheet metal screws (j). (Several positions are poss-

ible by selecting the mounting holes on the socket holder and

rotating the rubber seal)

Lead cable loosely through the strain relief (k) and screw in

place with the 2 sheet metal screws. Depending on the instal-

lation situation, the cable can be led out of the socket holder

through one of the three recesses.

B 3.9 x 33

(3 x)

PT 4 x 10

Figure 30

Secure safety socket to the (plastic) shaft cover of the caravan

with 4 screws, nuts and washers.

M4 x 16

(4 x)

Washer 4.3

(4 x)

Nut M4 (4 x)

Figure 31

No holes must be drilled in the chassis.

Alternatively, the safety socket can be secured using the two

hose clamps.

Figure 32

Route both wires to the control unit (shortening them if necess-

ary) and connect them to the connector block as shown in the

connecting diagram.

Re-check whether all cables are correctly connected, attached

using the provided clips and cannot chafe.

Function check

Check whether the battery is fully charged for operating the

Mover®XT4.

Position the caravan on open, level ground and apply the

parking brake. The drive rollers must not be in contact with

the wheels and the corner jacks must be raised.

Connect the battery terminals to the battery. Check that all

cables are securely attached and not hot, and that there are

no signs of short circuits etc.

Plug the 13-pin plug / adapter into the safety socket.

Move slide switch on remote control to the “On” position.

This switches on the remote control, and green LED 4 flashes

until the control unit is ready for operation. If LED 4 does not

light up, check polarity and condition of batteries in remote

control.

Check whether the drive motors are stationary. With the re-

mote control switched on, operate the “slide control (C)” and

the drive motors must rotate.

Engage drive rollers using remote control.

Ensure that there are no obstacles around the caravan and re-

lease the parking brake. Now check all functions several times

in accordance with the operating instructions.

Apply caravan parking brake. Disengage drive rollers and

move remote control slide switch to “Off” £ in order to switch

off the remote control and the Mover®XT4. Re-check distance

between drive rollers and tyres. Re-adjust if necessary.

The distance between the disengaged drive rollers

and tyres is 20 mm.

Warnings

The installer or vehicle owner must apply the yellow sticker

with the warning information, which is enclosed with the ap-

pliance, in a location in the vehicle where it is clearly visible

to all users (e.g. the wardrobe door). Missing stickers can be

requested from Truma.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover XT 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Truma Mover XT 4 Manual

Product: