484673

Truma Mover Mover H SE Manual

17
Zoom out
Zoom in
Previous page
1/76
Next page
17
Installation instructions
Read the installation instructions prior to starting work and
follow them carefully!
Please ensure that no metal chips or other contaminants get
into the controller during installation.
Intended use
The Mover H SE / H TE may only be mounted to Hobby vehi-
cle frames that are prepared for the Mover H SE / H TE and
for an approved angle bracket (see “Identifying the angle
bracket”).
The Mover H SE is designed for use on single-axle caravans
with a gross weight of up to 1800 kg,
and the Mover H TE is designed for use on dual-axle cara-
vans with a gross weight of up to 2250 kg.
The Mover H SE / H TE weighs approx. 26 kg.
Check the towing load of your vehicle and the gross weight of
your caravan in order to establish whether they are designed
for the additional weight.
Approval
The Truma Mover H SE / H TE has design approval, and a
general operating permit (ABE) has been issued for Germany.
Acceptance by a vehicle expert is not required. The ABE must
be kept in the vehicle.
The Mover H SE / H TE complies with the vehicle engine inter-
ference suppression directive 72/245/EEC with supplements
2004/104/EC, 2005/83/EC and 2006/28/EC and bears type
approval number: e1 03 4473
The Mover H SE / H TE complies with EMC directive 89/336/EEC
(2004/108/EC) and low voltage directive 73/23/EEC.
The remote hand set and the receiver comply with the
requirements of the R&TTE directive 1995/5/EC.
The Mover H SE / H TE satisfies the Machinery Directive
2006/42/EC.
The technical and administrative regulations of the country in
which the vehicle is initially registered must be complied with
when the Mover is being installed.
Guarantee claims, warranty claims and acceptance of liability
will be ruled out in the event of the following:
– modifications to the unit (including accessories),
– failure to use original Truma parts as
replacement parts and accessories,
– failure to follow the installation and operating instructions.
In addition to this, the operational approval for the device will
be cancelled.
Tools and facilities required
To install the unit you will need:
17 mm socket wrench, ring spanner or open-jawed spanner
Torque wrench (20 – 70 Nm)
Cable cutter/Crimping tool
Power drill/screwdrivers / 25 mm hole cutter
Portable 2 tonne trolley jack and axle stands to suit
Appropriate lighting.
Identifying the angle bracket
It is possible to mount the Mover using an angle bracket
on vehicle frames of the company Hobby from the vehicle
frame numbers XXX.YY.X.YY.X.Y.F901055 and XXX.YY.X.YY.
X.Y.F930814 of the year 2009.
Depending on the vehicle frame (1) and tyre type (2), a suita-
ble angle bracket (3) needs to be identified. This angle bracket
is available from Hobby dealers.
1
2
3
Vehicle frame (1)
trade name
company Hobby
Tyre type (2) Angle bracket (3)
art.-No.
company Hobby
400 – 460 195/70 R14
185 R14 C
1209990009
495, 500 185 R14 C 1209990909
540 – 560 195/70 R15 C
185 R14 C
1209990309
610 – 650 155 R13 C 1209990109
With increased GVW
610 – 650 165 R13 C 1209990209
690 – 720 165 R13 C – *
* Mounting of Mover H TE with angle bracket is not possible,
but it is convenient for Truma Mover TE.
It is not permitted to mount the Mover H SE / H TE
to caravans / towed vehicles with other frames
and without angle brackets!
Any drilling or welding to the chassis is not allowed. Under no
circumstances remove any suspension components from the
chassis.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Mover Mover H SE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover Mover H SE in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 7,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info