484651

Truma Mover H TE R Manual

18
Zoom out
Zoom in
Previous page
1/76
Next page
18
Identifying the angle bracket
It is possible to mount the Mover® using an angle bracket
on vehicle frames of the company Hobby from the vehicle
frame numbers XXX.YY.X.YY.X.Y.F901055 and XXX.YY.X.YY.
X.Y.F930814 of the year 2009.
Depending on the chassis (1) and the type of wheels (2), a
suitable angle bracket is required (3).
The angle support is only supplied by Hobby. Please con-
tact a dealer of the company Hobby.
1
2
3
It is not permitted to mount the Mover® H SE R /
H TE R to caravans / towed vehicles with other
frames and without angle brackets!
Any drilling or welding to the chassis is not allowed. Under no
circumstances remove any suspension components from the
chassis.
Assembly of the Mover®
The frame of the vehicle must be kept free of rust and heavy
soiling and without any damages to the suspension
components.
The wheels and tyres that are fitted to the caravan must be of
the same size and model and inflated as per the manufacturer’s
instructions.
Remove all components from packing and place on the floor.
In order to maintain the validity of the General Operat-
ing Permit (ABE), the provided factory plates (f) must be
attached on the left and right sides of the cross strut between
the drive unit retaining plates.
f
Read the installation instructions prior to starting work and
follow them carefully!
Please ensure that no metal chips or other contaminants get
into the controller during installation.
Intended use
The Mover® H SE R / H TE R may only be mounted to Hobby
vehicle frames that are prepared for the Mover® H SE R /
H TE R and for an approved angle bracket (see “Identifying
the angle bracket”).
The Mover® H SE R is designed for use on single-axle cara-
vans with a gross weight of up to 2000 kg,
and the Mover® H TE R is designed for use on dual-axle cara-
vans with a gross weight of up to 2250 kg.
The Mover® H SE R / H TE R weighs approx. 26 kg.
Check the towing load of your vehicle and the gross weight of
your caravan in order to establish whether they are designed
for the additional weight.
Approval
The Truma Mover® H SE R / H TE R has design approval, and a
general operating permit (ABE) has been issued for Germany.
Acceptance by a vehicle expert is not required. The ABE must
be kept in the vehicle.
The Mover® satisfies other requirements stated in the EC di-
rectives and standards (see declaration of conformity).
The technical and administrative regulations of the country in
which the vehicle is initially registered must be complied with
when the Mover® is being installed.
Guarantee claims, warranty claims and acceptance of liability
will be ruled out in the event of the following:
modifications to the unit (including accessories),
failure to use original Truma parts as replacement parts and
accessories,
failure to follow the installation and operating instructions.
In addition to this, the operational approval for the device will
be cancelled.
Tools and facilities required
To install the unit you will need:
17 mm socket wrench, ring spanner or open-jawed spanner
Torque wrench (5 – 70 Nm)
Cable cutter/Crimping tool
Power drill/screwdrivers / 25 mm hole cutter
Portable 2 tonne trolley jack and axle stands to suit
Appropriate lighting.
–
–
–
–
–
–
–
–
–
Installation instructions
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Mover H TE R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover H TE R in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 9,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info