631210

Truma BGE 10 Manual

9
Zoom out
Zoom in
Previous page
1/44
Next page
Push boiler with cowl part (1) through the cowl opening (2),
allowing it to protrude approx. 5mm out of the outer wall. Fit
the sealing frame (3) (as a result of the anti-twist protection
the frame can only be fitted in the correct position). Pre-drill
holes for the 6 fastening screws (4).
4
1
3
2
Figure 3
Remove sealing frame (3) and coat on the vehicle side with a
plastic body sealant – not silicone.
The sealing frame must be well sealed to the front
faces and cross-braces of the cowl part (1) and to the
outer wall.
Attach the sealing frame (3) to the cowl part with
4thread-forming screws (4).
4
3
Figure 4
Screw on the sealing frame (3) together with the
cowl part (1) so that the anti-twist protection
protrudes.
9
7
4
6
1
3
5
8
Figure 5
Seal the air gap between the hole (6) and the condensation
pipe (7) with plastic body sealant – not silicone.
Fit cowl grille (8). Press complete cowl onto vehicle wall and
mount using 6 screws (5).
Screw boiler securely to a suitable surface (plywood board,
laminated wooden battens or metal floor) on the vehicle floor
using at least two brackets (9) with the B5.5x25 screws
supplied.
Selecting a location
The device must always be installed in such a way that it is
easy to access at all times for service work, and also easy to
remove and install.
Position the boiler in such a way that the cowl can be fitted to
an outer surface that is as straight and smooth as possible.
The wind must be able to flow around this outer surface at all
sides, and no decorative strips or panels should be present
there if possible, otherwise place the boiler on a suitable base.
The wall cowl must be attached such that there is no fuel tank
filler neck or fuel tank breather opening within 500mm (A).
There must also be no living area ventilation openings within
300 mm (A). If the cowl has been placed vertically beneath an
opening window, the boiler must be equipped with an auto-
matic shut-off device in order to prevent operation with the
window open.
Window
Floor
300 mm
300 mm
protected
area
protected
area
A
Figure 1
The boiler must not be installed close to or directly behind a
room heater.
In order to ensure that there is sufficient ventilation to cool
the electronics, the gap between the electronics cover (34)
and the walls of furniture items in which the boiler is installed
must be at least 20mm.
Installing the boiler
Position the template for the cowl opening on the inner sur-
face of the wall.
A = Bottom edge of boiler
B = Lateral edge of boiler
Drill 4 holes (C) with a diameter of 10mm through the wall.
Drill hole (E) with a diameter of 15mm for the condensation
pipe (this can also be done from the outside = F).
Position the template on the outer surface of the wall. Mark-
ings(C) must be positioned over the holes drilled for the open-
ing. Use a saw to cut out the cowl opening (D) (92x168 mm).
If the gap between the outer wall and the boiler is more
than 35mm, cowl extension VBO2 will be required with an
extra length of 50mm. Cut along the dotted line with a saw
(100x176mm).
*
Line any cavities in the vicinity of
the cowl opening with wood so
that the screws can be tightened
firmly. The final cut-out should
be 168mm high by 92mm wide.
(*Sectional diagram for clarifi-
cation purposes)
Figure 2
Cut out or support trim strips or the like on the vehicle so that
the cowl is level.
If the walls are sloping, support the boiler. The angle of tilt
must not exceed 10degrees.
9
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma BGE 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma BGE 10 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 5,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Truma BGE 10

Truma BGE 10 User Manual - English, German, Dutch, Danish, French, Italian, Swedish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info