629213

Troy-Bilt 26J MiniRider - TB30R Manual

13
Zoom out
Zoom in
Previous page
1/72
Next page
13Section 3 — ASSembly & Set-Up
Install The Rear Engine Cover
 Remove the two factory installed hex screws located on
the rear engine cover mounting bracket. Retain the screws

2. Install the rear engine cover by positioning it in place as

into the slots provided, then rotate it backwards to align
the mounting holes.
Figure 3-10
3. Secure the cover with the two hex screws previously
removed. Do not to over-tighten.
Installing the Hitch Plate
 Remove the factory installed hitch plate mounting

2. Position the hitch plate, packed with the loose parts, with

two bolts and hex nuts previously removed.
Figure 3-11
Connecting the Battery Cables
CALIFORNIA PROPOSITION 65 WARNING:
Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
CAUTION: When attaching battery cables, always

followed by the NEGATIVE (Black) wire.
For shipping reasons, both battery cables on your equipment
may have been left disconnected from the terminals at the
factory. To connect the battery cables, proceed as follows:
NOTE: The positive battery terminal is marked Pos. (+). The
negative battery terminal is marked Neg. (–).
 Remove the factory installed hex bolts and sems nuts
located on the end of the wiring harness. Retain the
hardware for later instructions.
2. Remove the plastic cover, if present, from the positive
battery terminal and attach the red cable to the positive
battery terminal (+) with one of the bolts and hex nuts,
previously removed, using a / inch wrench and socket.

Figure 3-12
3. Remove the plastic cover, if present, from the negative
battery terminal and attach the black cable to the negative
battery terminal (–) with the remaining bolt and hex nut.

 Position the red rubber boot over the positive battery
terminal to help protect it from corrosion.
NOTE: If the battery is put into service after the date shown
on top/side of battery, charge the battery as instructed in

operating the tractor.
13
… 13 …


Need help? Post your question in this forum.

Forumrules
1

Forum

troy-bilt-26j-minirider---tb30r

Reset search

  • 26j mini rider rear wheels locked. worked before back`fire when trying to start and although shifter car be moved, the tranny seem to be in gear. Submitted on 21-9-2021 at 20:52

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Troy-Bilt 26J MiniRider - TB30R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Troy-Bilt 26J MiniRider - TB30R in the language / languages: English as an attachment in your email.

The manual is 8,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info