580088

Trotec TTR 5000 Manual

17
Zoom out
Zoom in
Previous page
1/50
Next page
B - 5 Operating manual dehumidifier TTR 5000
G
G
Operating manual dehumidifier TTR 5000 B - 6
B - 6 Operating manual dehumidifier TTR 5000
G
1. Control cabinet
2. Regeneration air outlet
3. Regeneration air inlet
4. Process air inlet
5. Process air outlet
05. Operation with electric element heater
Switching on
1. Close and lock the control cabinet doors.
2. Turn main switch and „Schalter Reg. Heizung“ into position 1.
„Störung Phasen“ lights up. Switch on „Drehfeld Umschaltung“.
3. The ‘Standby’ indicator lamp lights up.
4. Press the ‘ON’ button.
5. The ‘Standby’ indicator lamp goes out and the ‘Operation’ indicator
lamp lights up. If necessary switch on the „Regelstufenabschal-
tung“ (auxiliary heating).
All drives, including the heating, are now switched on and the dehu-
midifier is operating.
ATTENTION!
THE APPLIANCE WON’T START IF THE „SCHALTER REG-HEIZUNG“
IS NOT INTO POSITION 1.
Switching off
1. Press the ‘OFF’ button.
2. The ‘Operation’ indicator lamp goes off and the heater and the pro-
cess air fan switch off. The regeneration air fan runs on for approx.
3-5 minutes, in order to exhaust the stored heat from the heater.
This running-on is terminated automatically.
- it is possible to restart the dryer during running on.
- the dryer should only be switched off by the main switch installed in
the mains supply line in an emergency, because this will also in-
terrupt the running-on control and a thermostat error message can
appear.
Function of the electric air heater
The heater consists of 3 individual stages. This results in an increase
in the temperature of the regeneration air to approx. 120°C, which is
necessary for the regeneration of the dryer. Two heating stages are
always switched on as basic load stages.
If the full regeneration energy is not required for the drying procedure,
then the control thermostat (5B1) switches the control stage off de-
pending on the regeneration exhaust air temperature. The regenerati-
on temperature is then reduced.
The thermostats are marked separately and are accessible by opening
the service doors.
Factory thermostat settings
Please refer to the technical data sheet in the appendix of this opera-
ting manual.
06. Triggering of the safety devices and messages
Motor faults
If the motor protection breaker for the regeneration air fan trips due to
an overload, then the dehumidifier will be switched off automatically. If
the motor protection breakers for the process air fan and the rotor drive
trip due to an overload, then the dehumidifier will continue in running-on
mode. The ‘Motor fault’ indicator lamp lights up. Following rectification of
the fault, the black reset button on the motor protection breaker must be
pressed again and the fault must be unlocked with the reset button 4S1.
Thermostat faults
If the safety or maximum thermostat switches off due to over-tem-
perature, then the ‘Thermostat fault’ indicator lamp lights up. In or-
der to restore the standby condition of the dehumidifier after cooling
down, proceed as follows:
- Press the red reset button on the maximum temperature limiter
4F2 and on the safety thermostat 4F1. Subsequently acknowledge
with the reset button 4S2 on the control cabinet.
Electric heater faults
The individual heating stages of the regeneration air heater are pro-
tected by over-current trips. In the event of a short circuit or over-
loading, the heating stage concerned is switched off and the ‘Heater
fault’ lamp lights up. After rectifying the fault, the black reset button
on the overcurrent trip must be pressed again (unlocking).
Standby
The electrical power is connected to the dehumidifier, the rotary field
of the mains supply is correct and there is no error. The dehumidifier
can be switched on via button 5S1.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec TTR 5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec TTR 5000 in the language / languages: English, German, French, Turkish as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info