Manual Trotec TTK66E (page 2 of 23) (English)

726873

Zoom out

Zoom in

1/23

TRT-BA-TTK54E/TTK66E-TC2019-28-003-EN

TTK 54 E / TTK 66 E

OPERATING MANUAL

DEHUMIDIFIER

2 EN

dehumidifier TTK 54 E / TTK 66 E

Table of contents

Notes regarding the operating manual.................................2

Safety .....................................................................................2

Information about the device................................................5

Transport and storage...........................................................6

Assembly and installation.....................................................7

Operation ...............................................................................8

Errors and faults..................................................................11

Maintenance ........................................................................13

Technical annex...................................................................16

Disposal ...............................................................................22

Notes regarding the operating manual

Symbols

Danger

This symbol indicates dangers to the life and health of

persons due to extremely flammable gas.

Warning of electrical voltage

This symbol indicates dangers to the life and health of

persons due to electrical voltage.

Warning

This signal word indicates a hazard with an average

risk level which, if not avoided, can result in serious

injury or death.

Caution

This signal word indicates a hazard with a low risk

level which, if not avoided, can result in minor or

moderate injury.

Note

This signal word indicates important information (e.g.

material damage), but does not indicate hazards.

Info

Information marked with this symbol helps you to carry

out your tasks quickly and safely.

Follow the manual

Information marked with this symbol indicates that the

operating manual must be observed.

You can download the current version of the operating manual

and the EU declaration of conformity via the following link:

TTK 54 E

https://hub.trotec.com/?id=40260

TTK 66 E

https://hub.trotec.com/?id=40261

Safety

Read this manual carefully before starting or using the

device. Always store the manual in the immediate vicinity

of the device or its site of use!

Warning

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may

result in electric shock, fire and/ or serious injury.

Save all warnings and instructions for future

reference.

This appliance can be used by children aged from

8years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe

way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by children

without supervision.

• Do not use the device in potentially explosive rooms.

• Do not use the device in aggressive atmosphere.

• Set the device up in an upright and stable position.

• Let the device dry out after a wet clean. Do not operate it

when wet.

• Do not use the device with wet or damp hands.

• Do not expose the device to directly squirting water.

• Never insert any objects or limbs into the device.

• Do not cover or transport the device during operation.

• Do not sit on the device.

EN 3

dehumidifier TTK 54 E / TTK 66 E

• This appliance is not a toy! Keep away from children and

animals. Do not leave the device unattended during

operation.

• Check accessories and connection parts for possible

damage prior to every use of the device. Do not use any

defective devices or device parts.

• Ensure that all electric cables outside of the device are

protected from damage (e.g. caused by animals). Never

use the device if electric cables or the power connection

are damaged!

• The electrical connection must correspond to the

specifications in chapter Technical data.

• Insert the mains plug into a properly secured mains

socket.

• Observe the device's power input, cable length and

intended use when selecting extensions to the power

cable. Completely unroll extension cables. Avoid electrical

overload.

• Before carrying out maintenance, care or repair work on

the device, remove the mains plug from the mains socket.

Hold onto the mains plug while doing so.

• Switch the device off and disconnect the power cable from

the mains socket when the device is not in use.

• Do not under any circumstances use the device if you

detect damages on the mains plug or power cable.

If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

Defective power cables pose a serious health risk!

• When positioning the device, observe the minimum

distances from walls and other objects as well as the

storage and operating conditions specified in the Technical

data chapter.

• Make sure that the air inlet and outlet are not obstructed.

• Make sure that the suction side is kept free of dirt and

loose objects.

• Do not remove any safety signs, stickers or labels from the

device. Keep all safety signs, stickers and labels in legible

condition.

• Only transport the device in an upright position with an

emptied condensation tank or drain hose.

• Discharge the collected condensate before transport and

storage. Do not drink it. Health hazard!

Safety warnings for dehumidifiers filled with R290

• Only position the device in rooms where potentially leaking

refrigerant cannot accumulate.

• Only position the device in rooms where there is no

permanent source of ignition (e.g. open flames, an active

gas appliance or an electric heater).

• Please note that the refrigerant is odourless.

• Only install the device in compliance with the national

installation regulations.

• Observe the national gas regulations.

• Only install, operate and store the device

TTK 54 E/ TTK 66 E in a room measuring more than 4m

• Store the device in a way that no mechanical damage can

occur.

• Please note that the connected ducts must not contain any

sources of ignition.

• R290 is a refrigerant that complies with European

environmental regulations. No part of the cooling circuit

may be perforated.

• Do not drill through or burn.

• Do not use any means other than those recommended by

the manufacturer for accelerating the defrosting process.

• Every person working with or at the refrigerant circuit must

be able to provide a certificate of qualification issued by a

body accredited by the industry, demonstrating their

competence in the safe use of refrigerants based on a

procedure well-known in the industry.

• Service work may only be carried out in accordance with

the manufacturer's specifications. If maintenance and

repair work require the support of additional persons, the

person trained in handling flammable refrigerants shall

continuously supervise the work carried out.

• Unventilated rooms, in which the device is installed,

operated or stored, must be built in a way to ensure that

potentially leaking refrigerant cannot accumulate. This

serves to avoid fire or explosion hazards resulting from an

ignition of the refrigerant by an electric furnace, cooking

stove or another ignition source.

• The entire refrigerant circuit is a maintenance-free,

hermetically sealed system and may only be maintained or

repaired by specialist companies for cooling and air-

conditioning or by Trotec.

4 EN

dehumidifier TTK 54 E / TTK 66 E

Intended use

Only use the device for drying and dehumidifying room air, while

adhering to and following the technical data.

In addition, the device may also be used as a kind of clothes

dryer to dry wet laundry.

Intended use comprises:

• dehumidifying and drying:

– living rooms, bedrooms, bathrooms and basements

– laundries, holiday homes, camper vans, boats

• maintaining the dryness of:

– storage spaces, archives, laboratories, garages

– bathrooms, wash rooms, changing rooms etc.

Improper use

The device is not intended for industrial use.

• Do not place the device on wet or flooded ground.

• Do not place any objects, e.g. clothing, on the device.

• Do not use the device outdoors.

• Any unauthorised modifications, alterations or structural

changes to the device are forbidden.

• Any operation other than as described in this manual is

prohibited. Non-observance renders all claims for liability

and guarantee null and void.

Personnel qualifications

People who use this device must:

• be aware of the dangers that occur when working with

electric devices in damp areas.

• have read and understood the operating manual, especially

the Safety chapter.

Maintenance tasks which require the housing to be opened

must only be carried out by specialist companies for cooling and

air-conditioning or by Trotec.

Safety signs and labels on the device

Note

Do not remove any safety signs, stickers or labels from

the device. Keep all safety signs, stickers and labels in

legible condition.

The following safety signs and labels are attached to the device:

TTK54E/ TTK66E

Follow the manual

This symbol indicates that the operating manual must

be observed.

Follow the repair manual

Disposal, maintenance and repair work of the

refrigerant circuit may only be carried out in

accordance with the manufacturer's specifications and

by persons having a certificate of qualification. A

corresponding repair manual is available from the

manufacturer upon request.

EN 5

dehumidifier TTK 54 E / TTK 66 E

Residual risks

Danger

Natural refrigerant propane (R290)!

H220 – Extremely flammable gas.

H280 – Contains gas under pressure; may explode if

heated.

P210 – Keep away from heat, sparks, open flames and

other ignition sources. No smoking.

P377 – Leaking gas fire: Do not extinguish, unless leak

can be stopped safely.

P410+P403 – Protect from sunlight. Store in a well-

ventilated place.

Warning of electrical voltage

Work on the electrical components must only be

carried out by an authorised specialist company!

Warning of electrical voltage

Before any work on the device, remove the mains plug

from the mains socket!

Hold onto the mains plug while pulling the power cable

out of the mains socket.

Warning

Dangers can occur at the device when it is used by

untrained people in an unprofessional or improper way!

Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the

hands of children.

Warning

Risk of suffocation!

Do not leave the packaging lying around. Children may

use it as a dangerous toy.

Note

Do not operate the device without an inserted air filter!

Without the air filter, the inside of the device will be

heavily contaminated. This could reduce the

performance and result in damage to the device.

Behaviour in the event of an emergency

1. Switch off the device.

2. In an emergency, disconnect the device from the mains

feed-in: Hold onto the mains plug while pulling the power

cable out of the mains socket.

3. Do not reconnect a defective device to the mains.

Information about the device

Description of the device

The device uses the principle of condensation to automatically

dehumidify rooms.

The fan sucks damp room air through the air inlet, the air filter,

the evaporator and to the condenser located behind it. The air is

cooled at the cold evaporator until it is below the dew point.

Water vapour contained in the room air precipitates on the

evaporator fins as condensation or rime. The dehumidified,

cooled air is slightly warmed at the condenser and blown out

again. The drier air thus conditioned mixes with the air in the

room. The humidity in the room where the device is positioned

is reduced as air constantly circulates through the device.

Depending on the air temperature and the relative humidity, the

condensed water either drops continuously or only during the

defrost phase through the integrated drain nozzle into the

condensation tank below. It is fitted with a float to measure the

filling level.

The device has a control panel for operating and controlling the

functions.

Once the maximum filling level of the condensation tank is

reached or if the tank is not installed correctly, the condensation

tank indicator light on the control panel will be illuminated and

an error code will be displayed as well (see chapter Operating

elements). The device switches off. The indications only

disappear once the emptied condensation tank is reinserted.

Optionally, the condensed water can be drained by attaching a

hose at the condensation connection.

The device can reduce the relative humidity of a room to approx.

35%.

In addition, the device may also be used as a kind of clothes

dryer to dry wet laundry in living or working spaces.

Because of the heat radiation generated during operation, the

room temperature may rise slightly.

6 EN

dehumidifier TTK 54 E / TTK 66 E

Device depiction

MODE ON/OFFTIMERTURBO

ION

O

Full

Dryer

SMDCont.

No. Designation

1 Control panel

2 Transport handle

3 Wheels

4 Air inlet with air filter

5 Power cable holder

6 Condensation drain hose

7 Condensation drain hose connection

8 Condensation tank with filling level indicator

9 Air outlet

Transport and storage

Note

If you store or transport the device improperly, the

device may be damaged.

Note the information regarding transport and storage of

the device.

Transport

To make the device easier to transport, it is fitted with a carry

handle.

To make the device easier to transport, it is fitted with wheels.

Before transporting the device, observe the following:

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Do not use the power cable to drag the device.

• Drain the remaining condensate from the device and the

condensation drain hose (see chapter Maintenance).

• Only wheel the device on a level and smooth surface.

After transporting the device, observe the following:

• Set up the device in an upright position after transport.

• Leave the device to rest for 12to24hours, so the

refrigerant can accumulate within the compressor. Wait

12to24hours before switching the device back on! Acting

contrary might lead to compressor damage and a

malfunctioning device. If so, any warranty claims will be

voided.

Storage

Before storing the device, proceed as follows:

• Drain the remaining condensate from the device and the

condensation drain hose (see chapter Maintenance).

• Empty and clean the condensation tank and the

condensation drain hose prior to storage.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

When the device is not being used, observe the following

storage conditions:

• Only store the device in a room measuring more than 4m

• dry and protected from frost and heat

• in an upright position where it is protected from dust and

direct sunlight

• with a cover to protect it from invasive dust, if necessary

• Place no further devices or objects on top of the device to

prevent it from being damaged.

EN 7

dehumidifier TTK 54 E / TTK 66 E

Assembly and installation

Scope of delivery

• 1x Device

• 1x condensation drain hose, length: 0.6 m,

diameter: 14 mm

• 1x air filter

• 1x Manual

Unpacking the device

1. Open the cardboard box and take the device out.

2. Completely remove the packaging.

3. Fully unwind the power cable. Make sure that the power

cable is not damaged and that you do not damage it during

unwinding.

Start-up

When positioning the device, observe the minimum distance

from walls or other objects as described in the Technical data

chapter.

• Before restarting the device, check the condition of the

power cable. If there are doubts as to the sound condition,

contact the customer service.

• Only position the device in rooms where potentially leaking

refrigerant cannot accumulate.

• Only position the device in rooms where there is no

permanent source of ignition (e.g. open flames, an active

gas appliance or an electric heater).

• Set the device up in an upright and stable position.

• Do not create tripping hazards when laying the power

cable or other electric cables, especially when positioning

the device in the middle of the room. Use cable bridges.

• Make sure that extension cables are completely unrolled.

• When positioning the device, keep a sufficient distance to

heat sources.

• Make sure that no curtains or other objects interfere with

the air flow.

• When positioning the device, particularly in wet areas,

secure it locally with an RCD (residual current device)

which complies with the respective regulations.

Inserting the air filter

Note

Do not operate the device without an inserted air filter!

Without the air filter, the inside of the device will be

heavily contaminated. This could reduce the

performance and result in damage to the device.

• Make sure that the air filter is installed before switching

the device on.

Inserting the condensation tank

• Ensure that the float inside the condensation tank is

inserted correctly.

• Ensure that the condensation tank is empty and inserted

correctly.

Connecting the power cable

• Insert the mains plug into a properly secured mains

socket.

8 EN

dehumidifier TTK 54 E / TTK 66 E

Operation

Notes:

• Avoid open doors and windows.

• After being switched on, the device operates fully

automatically.

• The fan permanently runs in dehumidification mode even

after the set nominal value has been reached until the

device is switched off.

Operating elements

10 11 12 13 14

1718

1920212223

No. Designation Meaning

10 TIMER LED Illuminated when the timer is

activated

11 Fan speed LEDs Fan speed indication:

Low

Med(ium)

High (low + med.)

12 Full LED Condensation tank full or not

inserted correctly

13 Dryer LED Laundry drying mode is enabled

14 Cont. LED Continuous operation is enabled

15 Comfort LED Comfort mode is enabled

16 Power LED Illuminated during operation

17 ON/OFF button Power button:

Switching the device on or off

18 MODEbutton Selection button for operating

modes:

Dehumidification (not indicated)

Dryer = laundry drying function

Cont. = continuous operation

Comfort = comfort mode

19 Increase value button Setting the relative room

humidity

Setting the number of hours for

the timer function

No. Designation Meaning

20 Segment display Indication of the current relative

room humidity level

Indication of the relative room

humidity level during set-up

Indication of the number of

hours during timer

programming

Display of error codes

21 Decrease value button Setting the relative room

humidity

Setting the number of hours for

the timer function

22 FAN button Setting high, medium or low fan

speed

23 TIMER button Switches the timer function on

or off

Info

An acoustic signal is emitted each time a setting is

activated.

Switching the device on

Once you have completely installed the device as described in

the Start-up chapter, you can switch it on.

1. Press the ON/OFF button(17).

ð The device starts in dehumidification mode.

Setting the operating mode

• Dehumidification

• Continuous operation

• Comfort mode

• Laundry drying function

Dehumidification

The device keeps running until reaching the desired relative

room humidity. Then the compressor switches off and the fan

keeps running. Once the desired relative room humidity is

exceeded, the compressor switches back on.

In this operating mode, the desired relative room humidity can

be set at any time in increments of 5% within a setting range of

35% to 85%.

1. Press the MODE button(18) until only the Power LED(16)

is lit.

2. Press the Increase value(19) or Decrease value button(21)

to select the relative room humidity.

ð The desired relative room humidity is indicated in the

segment display(20) for approx.5seconds. Then the

current relative room humidity is displayed again.

EN 9

dehumidifier TTK 54 E / TTK 66 E

Setting the desired relative room humidity

You can only change the relative room humidity in

dehumidification mode.

1. Press the Increase value(19) or Decrease value button(21)

to set the relative room humidity. Setting is possible within

the range between 35% and 85% in steps of 5%.

ð The desired relative room humidity is indicated in the

segment display(20) for approx.5seconds. Then the

current relative room humidity is displayed again.

Setting the fan speed

With this function you can choose between low, medium and

high fan speed. The fan speed can only be adjusted in

dehumidification mode. The default setting for the laundry

drying function is the highest level.

1. Repeatedly press the FAN button(22) to select the desired

fan speed.

Continuous operation

The device dehumidifies the air constantly and regardless of the

relative room humidity. The desired relative room humidity

cannot be adjusted in this operating mode.

1. Press the MODE button(18) until the Cont. LED(14) is lit.

ð Continuous operation is selected.

Info

For continuous operation the condensation drain hose

can be connected in order to continuously drain the

accumulating condensate.

Comfort mode

Comfort mode ensures an agreeable humidity level ranging

between 45% and 55%. Depending on the room temperature

the device automatically regulates the convenient humidity level

choosing a value from 45% – 50% – 55%.

In this operating mode it is not possible to regulate the humidity

level manually.

1. Press the MODE button(18) until the Comfort LED(15) is lit

to switch comfort mode on or off.

Setting the timer

For the device to switch on or off automatically after a

predefined number of hours (max. 24hrs) you can programme

the timer.

The timer can be programmed in increments of 0.5hours (0 to

10h) or in increments of 1hour (10 to 24h).

The timer can be set in all operating modes.

You can activate the function regardless of the device being

switched on or off.

Note

Do not leave the operating device unattended in a

freely accessible room with an activated timer.

Automatic switch-on

ü The device is switched off.

1. Press the TIMER button(23) to programme automatic

switch-on.

ð The TIMER LED(10) is lit.

ð The segment display(20) indicates the number of hours

until automatic switch-on. Standard: 0.0

2. Press the Increase value(19) and Decrease value

buttons(21) to set a number of hours until automatic

switch-on.

ð The number of hours is indicated on the segment

display(20) for approx.5s. Then the current humidity

level of the room will be indicated.

ð The timer setting equals the desired number of hours.

ð After the predefined time, the device switches itself on.

Automatic switch-off

ü The device is switched on.

1. Press the TIMER button(23) to programme automatic

switch-off.

ð The TIMER LED(10) is lit.

ð The segment display(20) indicates the number of hours

until automatic switch-off. Standard: 0.0

2. Press the Increase value(19) and Decrease value

buttons(21) to set a number of hours until automatic

switch-off.

ð The number of hours is indicated on the segment

display(20) for approx.5s. Then the current humidity

level of the room will be indicated.

3. The device keeps running until the given switch-off time

has expired or until the device is switched off manually.

ð The timer setting equals the desired number of hours.

ð After the predefined time, the device switches itself off.

Note

You can deactivate automatic switch-on and switch-off

by setting the respective number of hours back to 0 or

by manually switching the device on or off.

If error codeP2 is indicated on the segment

display(20), the timer is also disabled.

A full condensation tank can cause the device to be

switched off before the set number of hours until

automatic switch-off have elapsed.

Memory function

After a power failure during operation the device will

automatically be switched back on after a while. The selected

settings are saved. Any programmed timer settings will not be

saved.

Auto stop function

If the water tank is full, not inserted correctly or the relative

room humidity has been reached, the device will stop

automatically.

10 EN

dehumidifier TTK 54 E / TTK 66 E

Operation with hose attached to the condensation

connection

For continuous operation or unattended dehumidification, please

connect the supplied condensation drain hose to the device.

ü The supplied hose (diameter= 14mm) is ready for use.

ü The device is switched off.

1. Remove the rubber plug.

2. Push one end of the hose onto the hose connection.

3. Guide the other hose end to a suitable drain or sufficiently

dimensioned collection container. Please note that the

hose must not be kinked.

Remove the hose if you want to collect the condensate in the

condensation tank again. Allow the hose to dry prior to storage.

The hose can be connected in any operating mode for

continuous operation.

Automatic defrost

At low ambient temperatures, ice may form at the evaporator

during dehumidification. The device will then carry out an

automatic defrost. Dehumidification is briefly interrupted during

defrosting. The fan keeps running. Error codeP1 for automatic

defrost will be indicated on the segment display(20).

The duration of the defrost process can vary. Do not switch off

the device during automatic defrost. Do not remove the mains

plug from the mains socket.

EN 11

dehumidifier TTK 54 E / TTK 66 E

Drying laundry

In addition, the device may also be used as a kind of clothes

dryer to dry wet laundry in living or working spaces.

When positioning the device or a clothes horse, please observe

the minimum distances specified in the technical data.

For drying laundry the following values should be selected:

• cupboard dry = 46 % relative humidity

• iron dry = 58 % relative humidity

• slightly dried = 65 % relative humidity

If necessary, use a measuring device to determine the humidity

level.

The relative humidity cannot be adjusted in this operating mode.

The maximum operating time in this mode is 10hours.

1. Press the MODE button(18) until the Dryer LED(13) is lit.

ð The function for drying laundry is activated.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• If necessary, remove the condensation drain hose and any

residual fluid from it.

• Empty the condensation tank, if need be.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damage.

• Check the on-site fusing.

• Check the filling level of the condensation tank, and empty

it if necessary. The Full LED(12) must not light up. Error

codeP2 must not be indicated on the segment

display(20).

• Check the condensation tank for correct seating.

• Check the room temperature. Observe the device's

permissible operating range according to the technical

data. Possibly, the device does not start because the

ambient temperature is too low (< 5°C).

• Wait for 10minutes before restarting the device. If the

device is not starting, have the electrics checked by a

specialist company or by Trotec.

The device is running, but there is no formation of

condensate:

• Check the float in the condensation tank for dirt. If

necessary, clean the condensation tank. The float must be

able to move freely.

• Check the room temperature. Observe the device's

permissible operating range according to the technical

data. Possibly, the device does not start because the

ambient temperature is too low (< 5°C).

• Ensure that the relative room humidity complies with the

technical data.

• Check the preselected relative room humidity. The

humidity in the room must be above the selected range.

• Check the air filter for dirt. If necessary, clean or replace

the air filter.

• Check whether the device is running in comfort mode. In

this case, the compressor switches off automatically once

the relative room humidity is below 45%.

• From the outside, check the condenser for dirt (see

chapter Maintenance). If the condenser is dirty, have it

cleaned by a specialist company or by Trotec.

• The device might carry out an automatic defrost. During

automatic defrost, the device does not dehumidify.

12 EN

dehumidifier TTK 54 E / TTK 66 E

The device is loud or vibrates:

• Check whether the device is set up in a stable and upright

position.

Condensate is leaking:

• Check the device for leaks.

The compressor does not start:

• Check the room temperature. Observe the device's

permissible operating range according to the technical

data. Possibly, the device does not start because the

ambient temperature is too low (< 5°C).

• Ensure that the relative room humidity complies with the

technical data.

• Check the preselected relative room humidity. The

humidity in the room must be above the selected range.

• Check whether the device is running in comfort mode. In

this case, the compressor switches off automatically once

the relative room humidity is below 45%.

• Check whether the overheating protection of the

compressor has tripped. Disconnect the device from the

mains and let it cool down for approx. 10minutes before

reconnecting it.

• The device might carry out an automatic defrost. During

automatic defrost, the device does not dehumidify.

The device gets very warm, is loud or loses power:

• Check the air inlets and air filters for dirt. Remove external

dirt.

• From the outside, check the device for dirt (see chapter

Maintenance). If the inside of the device is dirty, have it

cleaned by a specialist company for cooling and air-

conditioning or by Trotec.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to a specialist company for cooling and air-conditioning

or to Trotec for repair.

Error codes

The following error messages can be displayed on the segment

display(20):

Error code Cause Remedy

AS Fault at humidity

sensor

Disconnect the device

briefly from the mains.

Should the error still be

displayed after the restart,

please contact the

customer service.

ES Fault at temperature

sensor

E3 General fault at the

device

EC Leaking refrigerant Switch the device off and

contact the customer

service.

P1 Automatic defrost This is not a fault. Wait for a

brief period. The indication

will disappear the moment

the automatic defrost

process is completed.

P2 Condensation tank

full or not inserted

correctly

Empty the condensation

tank or check the

condensation tank for

correct fit.

EN 13

dehumidifier TTK 54 E / TTK 66 E

Maintenance

Maintenance intervals

Maintenance and care interval before every

start-up

as needed at least every

2weeks

at least every

4weeks

at least every

6months

at least

annually

Check the air inlets and outlets for

dirt and foreign objects and clean if

necessary

X X

Clean the exterior

X X

Visually check the inside of the

device for dirt

X X

Check the air filter for dirt and

foreign objects and clean or

replace if necessary

X X

Replace the air filter

Check for damage

Check the attachment screws

X X

Test run

Empty the condensation tank and/

or drain hose

Maintenance and care log

Device type: .............................................

Device number: ....................................

Maintenance and care interval

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Check air inlets and outlets for dirt and

foreign objects and clean if necessary

Clean the exterior

Visually check the inside of the device

for dirt

Check the air filter for dirt and foreign

objects and clean or replace if

necessary

Replace the air filter

Check for damage

Check the attachment screws

Test run

Empty the condensation tank and/or

drain hose

Comments

1. Date: ...................................

Signature: ................................

2. Date: ....................................

Signature: .................................

3. Date: ....................................

Signature: .................................

4. Date: ....................................

Signature: .................................

5. Date: ...................................

Signature: ................................

6. Date: ....................................

Signature: .................................

7. Date: ....................................

Signature: .................................

8. Date: ....................................

Signature: .................................

9. Date: ...................................

Signature: ................................

10. Date: ..................................

Signature: .................................

11. Date: ..................................

Signature: .................................

12. Date: ..................................

Signature: .................................

13. Date: .................................

Signature: ................................

14. Date: ..................................

Signature: .................................

15. Date: ..................................

Signature: .................................

16. Date: ..................................

Signature: .................................

14 EN

dehumidifier TTK 54 E / TTK 66 E

Activities required before starting maintenance

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch the device off.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

Warning of electrical voltage

Tasks which require the housing to be opened

must only be carried out by authorised specialist

companies or by Trotec.

Refrigerant circuit

Danger

Natural refrigerant propane (R290)!

H220 – Extremely flammable gas.

H280 – Contains gas under pressure; may explode if

heated.

P210 – Keep away from heat, sparks, open flames and

other ignition sources. No smoking.

P377 – Leaking gas fire: Do not extinguish, unless leak

can be stopped safely.

P410+P403 – Protect from sunlight. Store in a well-

ventilated place.

• The entire refrigerant circuit is a maintenance-free,

hermetically sealed system and may only be maintained or

repaired by specialist companies for cooling and air-

conditioning or by Trotec.

Safety signs and labels on the device

Check the safety signs and labels attached to the device at

regular intervals. Replace illegible safety signs!

Cleaning the housing

Clean the housing with a soft, damp and lint-free cloth. Ensure

that no moisture enters the housing. Protect electrical

components from moisture. Do not use any aggressive cleaning

agents such as cleaning sprays, solvents, alcohol-based or

abrasive cleaners to dampen the cloth.

Visual inspection of the inside of the device for dirt

1. Remove the air filter.

2. Use a torch to illuminate the openings of the device.

3. Check the inside of the device for dirt.

4. If you see a thick layer of dust, have the inside of the

device cleaned by a specialist company for cooling and air-

conditioning or by Trotec.

5. Put the air filter back in.

Cleaning the air filter

Note

Ensure that the air filter is not worn or damaged. The

corners and edges of the air filter must not be

deformed or rounded. Before reinserting the air filter,

make sure that it is undamaged and dry!

The air filter has to be cleaned as soon as it is dirty. This is

brought to light e.g. by a reduced capacity (see chapter Errors

and faults).

1. Remove the air filter from the device.

EN 15

dehumidifier TTK 54 E / TTK 66 E

2. Clean the filter using a slightly damp, soft, lint-free cloth. If

the filter is heavily contaminated, clean it with warm water

mixed with a neutral cleaning agent.

3. Allow the filter to dry completely. Do not insert a wet filter

into the device!

4. Reinsert the air filter into the device.

Emptying the condensation tank

If the condensation tank is full or not inserted correctly, an

acoustic signal will be emitted. Moreover, the Full LED(12) will

be lit and error codeP2 indicated on the segment display(20).

The compressor and fan will switch off.

1. Take the condensation tank out of the device.

MODE ON/OFFTIMERTURBO

ION

O

Full

Dryer

SMDCont.

2. Empty the condensation tank into a drain or sink.

3. Rinse the tank with clear water. Clean the tank regularly

using a mild cleaning agent (no detergent!).

4. Refit the condensation tank into the device.

Make sure not to damage the float when inserting or

removing the condensation tank.

In doing so, make sure that the float is positioned

correctly.

In doing so, make sure that the condensation tank is

inserted correctly, since otherwise the device cannot be

switched back on.

MODE ON/OFFTIMERTURBO

ION

O

Full

Dryer

SMDCont.

Activities required after maintenance

If you want to continue using the device:

• Leave the device to rest for 12to24hours, so the

refrigerant can accumulate within the compressor. Wait

12to24hours before switching the device back on! Acting

contrary might lead to compressor damage and a

malfunctioning device. If so, any warranty claims will be

voided.

• Reconnect the device to the mains.

If you do not intend to use the device for a considerable time:

• Store the device according to the Storage chapter.

16 EN

dehumidifier TTK 54 E / TTK 66 E

Technical annex

Technical data

Parameter Value

Model TTK54E TTK66E

Max. dehumidification performance 16 l/24h 24 l/24h

Dehumidification performance @ 30°C and 80%RH 14 l/24h 20 l/24h

Air flow rate 150 m

/h 168 m

Ambient temperature 5°C to 32°C 5°C to 32°C

Operating range 35 % to 85 %RH 35 % to 85 %RH

Pressure suction side 1.0MPa 1.0MPa

Pressure outlet side 2.6MPa 2.6MPa

Max. permissible pressure 2.6MPa 2.6MPa

Power supply 1/N/PE~220–240V/ 50Hz 1/N/PE~220–240V/ 50Hz

Power consumption max. 0.43 kW 0.44 kW

Nominal current 2.2 A 2.3 A

Refrigerant R-290 R-290

Amount of refrigerant 75 g 75 g

GWP factor 3 3

equivalent 0.00023t 0.000225t

Condensation tank capacity 3 l 3 l

Sound pressure level (atadistance of1m) 46 dB(A) 46 dB(A)

Dimensions (lengthx widthx height) 245x 350x 510 mm 245x 350x 510 mm

Minimum distance to walls and other objects

A: top:

B: rear:

C: side:

D: front:

40 cm

20 cm

40 cm

20 cm

Weight 15 kg 15 kg

EN 17

dehumidifier TTK 54 E / TTK 66 E

Circuit diagram TTK 54 E

18 EN

dehumidifier TTK 54 E / TTK 66 E

Circuit diagram TTK 66 E

DISPLAY

BOARD

MAIN BOARD

F A N

P O W E R

CNN1100

CCNN11

CCNN33

CCNN55

PP88

CCNN44

CCNN22

WWAATTEERR

SSWWIITTCCHH

PPIIPPEE

TTEEMMPP..

HHUUMMII..

SSEENNSSOORR

BBLLAACCKK((oorr BBRROOWWNN))

RREEDD

WWHHIITTEE((oorr BBLLUUEE))

YY//GG

YY//GG((oorr GGRREEEENN))

AACC

BBLLUUEE

BBRROOWWNN

FFAANN

CCAAPPAACCIITTOORR

YY//GG

COMP.

BBLLUUEE

This symbol

indicates

the element

is optional,

the actual

shape shall

prevail

Notes:

OverLoad

Protector

PP77

PP44

RREEDD

BBLLAACCKK

ION

YY//GG

PP1100

((oorr CCNN66//CCNN66AA //CCNN66BB//CCNN66CC))

Bypass Valve

BBLLUUEE

PP1111

PP55

((oorr CCNN1133))

Notes: Display and Fan's conntors must be match the actual indicates.

CCNN1111

TOUCH

PANE L

POWER

BOARD

CCNN11

CCNN22

CCNN1144

CCNN1155

11 33

11 22

CCNN77

SSWWIITTCCHH

PP22

PP11

PPTTCC..

SSTTAARRTTEERR

16020100001092

CCNN1100

WWIIFFII

CCNN11

PUMP

D C P O W E R

BO A R D

CCNN22

RREEDD

OPT I ONA L

PP99

PP66

BBLLAACCKK((oorr BBLLUUEE))

RREEDD

BBLLAACCKK((oorr BBLLUUEE))

HHIITTEE

WWII

IITTEE((oorr YY

LLLLOOWW

EN 19

dehumidifier TTK 54 E / TTK 66 E

Overview of spare parts TTK54E Note: The position numbers of the spare parts differ from those

describing the positions of other parts mentioned in this

operating manual.

20 EN

dehumidifier TTK 54 E / TTK 66 E

Spare parts list TTK54E

NO. SPARE PART QTY. NO. SPARE PART QTY.

1 Water Tank Assembly

4.3 Fan Motor Capacitor

1.1 Water Tank Subassembly

5 Chassis Assembly

2 Front Panel Assembly

5.1 Chassis Subassembly

2.1 Front Panel Subassembly

5.2 Universal Wheel

2.1.1 Top Cover

6 Power Cord Subassembly

2.2 Display Box Subassembly

7 Pipe Teperature Sensor

3 Volute Shell Assembly

8 Fixed Speed Reciprocating Compressor

3.1 Volute Shell Subassembly

9 Suction Pipe Assembly

3.2 Centrifugal Fan

10 Capillary Assembly

3.3 Single Phase Asynchronous Motor

11 Condenser Assembly

3.4 Electronic Control Box

12 Evaporator Assembly

3.5 Humidity Sensor Board Module

13 Discharge Pipe Assembly

3.6 Dehumifier Main Control Board Subassembly

14 Rear Panel Subassembly

4 Middle Partition Board Assembly

15 Air Inlet Grille

4.1 Partition Board Subassembly

20 Cover Of Electronic Control Box

4.2 Micro Switch

EN 21

dehumidifier TTK 54 E / TTK 66 E

Overview of spare parts TTK66E Note: The position numbers of the spare parts differ from those

describing the positions of other parts mentioned in this

operating manual.

22 EN

dehumidifier TTK 54 E / TTK 66 E

Spare parts list TTK66E

NO. SPARE PART QTY. NO. SPARE PART QTY.

1 Water Tank Assembly

5 Chassis assembly

1.1 Water Tank Subassembly

5.1 Chassis subassembly

1.2 Dobber sase

5.2 Universal wheel

1.3 Handle of water tank

6 Power cord subassembly

2 Front panel assembly

7 Pipe temperature sensor

2.1 Front panel subassembly

8 Fixed speed reciprocating compressor

2.1.1 Top cover

9 Suction pipe assembly

2.2 Display box subassembly

10 Capillary assembly

3 Volute shell assembly

11 Condenser assembly

3.1 Volute shell subassembly

12 Evaporator assembly

3.5 Humidity sensor board module

13 Discharge pipe

3.6 Dehumidifier main control board subassembly

14 Rear panel assembly

4 Middle partition board assembly

15 Air inlet grille

4.1 Partition board subassembly

18 Srain stopper

4.2 Micro switch

25 Drain pipe

4.3 Fan motor capacitor

Disposal

The icon with the crossed-out waste bin on waste

electrical or electronic equipment stipulates that this equipment

must not be disposed of with the household waste at the end of

its life. You will find collection points for free return of waste

electrical and electronic equipment in your vicinity. The

addresses can be obtained from your municipality or local

administration. For further return options provided by us please

refer to our website www.trotec24.com.

The separate collection of waste electrical and electronic

equipment aims to enable the re-use, recycling and other forms

of recovery of waste equipment as well as to prevent negative

effects for the environment and human health caused by the

disposal of hazardous substances potentially contained in the

equipment.

Have the refrigerant (propane) disposed of appropriately and

according to the national regulations by a company with the

relevant certification (European Waste Catalogue 160504).

Trotec GmbH & Co. KG

Grebbener Str. 7

D-52525 Heinsberg

+49 2452 962-400

+49 2452 962-200

info@trotec.com

www.trotec.com

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Trotec TTK66E in the language / languages: English as an attachment in your email.

The manual is 3,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec TTK66E

Trotec TTK66E User Manual - German - 23 pages

Trotec TTK66E User Manual - Dutch - 24 pages

Trotec TTK66E User Manual - Danish - 23 pages

Trotec TTK66E User Manual - French - 26 pages

Trotec TTK66E User Manual - Italian - 25 pages

Trotec TTK66E User Manual - Polish - 26 pages

Trotec TTK66E User Manual - Portuguese - 25 pages

Trotec TTK66E User Manual - Swedish - 24 pages

Trotec TTK66E User Manual - Turkish - 26 pages

Trotec TTK66E User Manual - Spanish - 25 pages

Trotec TTK66E User Manual - Norwegian - 24 pages

Trotec TTK66E User Manual - Finnish - 24 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Trotec TTK66E Manual

Product: