756406
9
Zoom out
Zoom in
Previous page
1/11
Next page
EN 9
pyrometer TP7
Setting the upper and lower alarm thresholds
You can set both an upper and lower alarm threshold for the
measured value at the device. Upon exceeding or falling below
this value an acoustic signal will be emitted by the device.
Additionally, the display lights up in one of the following colours:
Display colour Meaning
Flashes red Surface temperature exceeds
activated upper threshold. The
display flashes red and a
constant alarm tone is emitted.
Also works when the display
illumination is deactivated.
Flashes blue Surface temperature below
activated lower threshold. The
display flashes blue and a
constant alarm tone is emitted.
Also works when the display
illumination is deactivated.
Continuously illuminated in
green
Surface temperature is in
normal range. The display will
only be illuminated in green if
the display illumination is
activated.
Please proceed as follows to set the upper and lower alarm
thresholds:
1. Repeatedly press the MODE button(6) until the
corresponding icon flashes in the Indication of the upper
alarm threshold(13)/ Indication of the lower alarm
threshold(14).
ðThe characters OFF appear on the upper measurement
value display(20).
2. Press the Laser button(7) or the Lamp button(5).
ðThe characters ON appear on the upper measurement
value display(20).
3. Then press the MODE button(6) again.
ðThe currently saved value for the alarm threshold will be
indicated on the upper measurement value display(20).
4. Use the Laser button(7) or the Lamp button(5) to change
the value for the alarm threshold as desired.
Enabling/ disabling the alarm threshold
Please proceed as follows to enable/ disable the upper and
lower alarm thresholds:
1. Repeatedly press the MODE button(6) until the
corresponding icon flashes in the Indication of the upper
alarm threshold(13)/ Indication of the lower alarm
threshold(14).
ðThe characters OFF appear on the upper measurement
value display(20).
2. Press the Laser button(7) or the Lamp button(5) to
activate the alarm threshold.
ðThe characters ON appear on the upper measurement
value display(20).
ðThe desired alarm threshold is now activated.
3. Press the Laser button(7) or the Lamp button(5) again to
deactivate the alarm threshold.
ðThe characters OFF appear on the upper measurement
value display(20).
ðThe desired alarm threshold is now deactivated.
Maintenance and repair
Battery change
A battery change is required, when a battery indication lights up
on the display(8) or the device can no longer be switched on.
See chapter Operation.
Cleaning
Clean the device with a soft, damp and lint-free cloth. Make
sure that no moisture enters the housing. Do not use any
sprays, solvents, alcohol-based cleaning agents or abrasive
cleaners, but only clean water to moisten the cloth.
Repair
Do not modify the device or install any spare parts. For repairs
or device testing, contact the manufacturer.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The device does not switch on:
Check the charging status of the battery. Change the
battery, if required (see chapter Inserting the battery).
Make sure that the battery is properly positioned. Check
the polarity is correct.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec TP7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec TP7 in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec TP7

Trotec TP7 User Manual - German - 11 pages

Trotec TP7 User Manual - Dutch - 11 pages

Trotec TP7 User Manual - French - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info