753925
7
Zoom out
Zoom in
Previous page
1/10
Next page
EN 7
LED work lamp PWLS 05-10 / PWLS 06-10
1. Open the battery compartment(6) by removing the battery
compartment cover(5).
2. Insert the batteries with correct polarity into the battery
compartment(6) (+/-).
3. Close the battery compartment(6) by closing it with the
battery compartment cover(5).
ðThe device PWLS 05-10 is now ready to use.
Charging batteries for PWLS 06-10
Note
The battery can be damaged in case of improper
charging.
Pull out the USB charging cable(13) from the external
charger each time before switching the device on.
Never charge the battery at ambient temperatures
below -20°C or above 55°C.
Charge the battery of PWLS 06-10 completely before using the
device. Use the USB charging cable(13) and a standard
charger.
Proceed as follows to charge the battery:
1. Open the cover(10) of the USB connections at the back of
the cordless work light.
2. If applicable, plug the charger into the mains socket.
3. Put the USB charging cable(13) into the USB connection/
input(9) of the device PWLS 06-10 and into a charger.
ðWhen the battery status is very low, the charging time is
6-7hours.
ðWhen the battery is charged 25%, the first LED of the
battery indication(12) is illuminated in blue. When the
battery is charged 50%, the second LED of the battery
indication(12) is illuminated in blue. When the battery is
charged 75%, the third LED of the battery
indication(12) is illuminated in blue.
ðWhen the battery is charged 100%, the fourth LED of
the battery indication(12) is illuminated in blue.
4. When all LEDs of the battery indication(12) are illuminated
and the battery is completely charged, you can remove the
USB charging cable(13) from the charger and from the
device PWLS 06-10.
5. Pull the charger out of the mains socket.
ðThe LED work light and the charger may have become
warm during charging. Let the LED work light and the
charger cool down to room temperature.
ðThe device PWLS 06-10 is now ready to use.
Note
Note that the battery status of the device PWLS06-10
cannot be read while in operation. You can only read
the battery status while charging.
Operation
Tips and notes on handling the LED work light
General information:
Avoid looking directly into the light source.
Use the devices only for a temporary illumination of indoor
and outdoor areas, e.g. for construction sites.
The devices PWLS 05-10 and PWLS 06-10 can be used as
strobe.
The LED work lights are particularly suited for illuminating
larger areas.
Info
You can turn the handles of the LED work lights by
180° and set 6 positions.
Switching the device on and off
Switching the devices PWLS05-10 and PWLS06-10 on and off
works identically.
1. Press the on/off switch(3/7) 1x to switch the device on or
off.
ðOnce the device is switched on, the surface LED(1) is
illuminated.
ðOnce the device is switched off, the surface LED(1) is
not illuminated.
Setting brightness level and strobe mode
Setting brightness level and strobe mode works identically for
both devices PWLS 05-10 and PWLS 06-10
üCheck whether the batteries (standard or integrated) are
completely charged. If necessary, replace the batteries or
charge the integrated battery.
1. Set the lowest light intensity by pressing the on/off
switch(3/7)1x.
2. Set the high brightness level by pressing the on/off
switch(3/7)3x.
3. Set the strobe mode by pressing the on/off
switch(3/7)5x.
Always proceed in the same order to set the desired light
intensity or the strobe mode.
Note
By quickly pressing the
on/off switch(3/7), you can switch between the
brightness levels and the strobe mode.
Using the power bank
If you like to use the device PWLS 06-10 as power bank,
proceed as follows:
1. Put the USB charging cable(13) into the USB connection/
output(8) of the device PWLS06-10.
2. Then plug the USB charging cable into the USB input of the
device that you would like to charge.
3. Charge your device until it has reached the desired
charging status.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PWLS 06-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PWLS 06-10 in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PWLS 06-10

Trotec PWLS 06-10 User Manual - German - 11 pages

Trotec PWLS 06-10 User Manual - Dutch - 11 pages

Trotec PWLS 06-10 User Manual - French - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info