753272
13
Zoom out
Zoom in
Previous page
1/18
Next page
EN 13
cordless drill driver PSCS 11-20V
Mounting the belt clip
Optionally, you can mount the belt clip included in the scope of
delivery to the device.
1. Set the switch for clockwise/ counter-clockwise
rotation(4) to centre position(lock).
2. Loosen the screw at the attachment(7) for the belt clip.
3. Fasten the belt clip(12) to the belt clip attachment(7) by
means of the screw.
4
7
12
Operation
Tips and notes on handling the cordless drill driver
General information:
Check the tool in the keyless drill chuck for correct fit
before every application. It must be firmly locked and
centred in the drill chuck.
Screw bits are marked with their size and shape. If you are
unsure, check whether the bit can be firmly tightened in
the keyless drill chuck without clearance.
The centre position of the clockwise/counter-clockwise
rotationswitch (lock) is suited for work breaks or (drill) bit
exchange.
Screwing:
In case of soft wood, screws can be screwed in without
pre-drilling.
In case of hard wood or large screws, it is recommended
to use a drill for pre-drilling.
When using countersunk screws, the drill hole should be
countersunk beforehand.
Especially smaller screws and bits may be damaged when
selecting an excessive torque and / or speed at the tool.
Drilling in general:
Take short breaks regularly during drilling. When doing so,
take the drill bit out of the drill hole so that the drill bit can
cool down.
Secure the workpiece in a tensioning device or vice.
Select the speed depending on the material characteristics
and the size of the drill bit:
High speed for small drilling diameter or soft material
Low speed for large drilling diameter or hard material
Use a suitable aid to mark the intended location of the drill
hole.
Select a low speed for spudding.
Drilling in metal:
Use suitable metal drill bits (e.g. drill bits made of
high-speed steel (HSS)).
For larger drilling diameters, use a smaller drill bit for
pre-drilling.
To achieve ideal results, the drill bit should be cooled with
a suitable lubricant.
Metal drill bits may also be used for drilling in plastic.
Drilling in wood:
Use drill bits suitable for wood.
Place a block of wood under the workpiece or drill in from
both sides so that the wood cannot break off when it is
being drilled through.
Use a wood drill bit with centring tip. For deep drill holes,
use an auger bit; for large drilling diameters, use a
Forstner bit.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PSCS11-20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PSCS11-20V in the language / languages: English as an attachment in your email.

The manual is 2,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PSCS11-20V

Trotec PSCS11-20V User Manual - German - 19 pages

Trotec PSCS11-20V User Manual - Dutch - 19 pages

Trotec PSCS11-20V User Manual - French - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info