753296
11
Zoom out
Zoom in
Previous page
1/18
Next page
EN 11
rotary hammer PRDS 05-230V
Using the keyless drill chuck (optional)
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
1. Insert the keyless drill chuck(7) into the SDS-plus system
tool holder(1) and, if necessary, slightly turn it until it
clicks into place.
1
7
2. Open the keyless drill chuck(7).
3. Insert the tool into the keyless drill chuck(7).
4. Tighten the keyless drill chuck(7).
7
5. Check the keyless drill chuck(7) and the inserted tool for
tight fit.
Info
Only use the optional keyless drill chuck in drilling
mode!
The function selector switch with release button(3)
must be set to position .
Connecting the power cable
1. Insert the mains plug into a properly secured mains
socket.
Operation
Tips and notes on handling the rotary hammer
Drilling in general:
Take short breaks regularly during drilling. When doing so,
take the drill bit out of the drill hole so that the drill bit can
cool down.
Secure the workpiece in a tensioning device or vice.
Select the speed depending on the material characteristics
and the size of the drill bit:
High speed for small drilling diameter or soft material
Low speed for large drilling diameter or hard material
Use a suitable aid to mark the intended location of the drill
hole.
Select a low speed for spudding.
Drilling in metal:
Use suitable metal drill bits (e.g. drill bits made of high-
speed steel (HSS)).
For larger drilling diameters, use a smaller drill bit for pre-
drilling.
To achieve ideal results, the drill bit should be cooled with
a suitable lubricant.
Metal drill bits may also be used for drilling in plastic.
Drilling in wood:
Use drill bits suitable for wood.
Place a block of wood under the workpiece or drill in from
both sides so that the wood cannot break off when it is
being drilled through.
Use a wood drill bit with centring tip. For deep drill holes,
use an auger bit; for large drilling diameters, use a
Forstner bit.
Impact drilling in masonry / bricks:
Use a drill bit suitable for masonry / bricks.
Chiselling in general:
Use a suitable chisel.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PRDS05-230V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PRDS05-230V in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PRDS05-230V

Trotec PRDS05-230V User Manual - German - 19 pages

Trotec PRDS05-230V User Manual - Dutch - 17 pages

Trotec PRDS05-230V User Manual - French - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info