753362
3
Zoom out
Zoom in
Previous page
1/15
Next page
TRT-BA-PPOS10-20V-TC2020-09-001-EN
PPOS 10-20V
EN
ORIGINAL INSTRUCTIONS
CORDLESS POLISHER
2 EN
cordless polisher PPOS 10-20V
Table of contents
Notes regarding the instructions ..........................................2
Safety .....................................................................................2
Information about the device................................................7
Transport and storage...........................................................9
Start-up..................................................................................9
Operation .............................................................................11
Available accessories..........................................................12
Errors and faults..................................................................12
Maintenance ........................................................................13
Disposal ...............................................................................14
Declaration of conformity ...................................................14
Notes regarding the instructions
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information
(e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Wear safety glasses
Information marked with this symbol indicates that you
should wear eye protection.
Wear a protective mask
Information marked with this symbol indicates that you
should wear a protective mask.
You can download the current version of the instructions and
the EUdeclaration of conformity via the following link:
PPOS 10-20V
https://hub.trotec.com/?id=44253
Safety
General Power Tool Safety Warnings
Warning
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term power tool in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
General Power Tool Safety Warnings– Work area
safety
Keep work area clean and well lit. Clutter or dark areas
invite accidents.
Do not operate power tools in explosive atmosphere,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
EN 3
cordless polisher PPOS 10-20V
General Power Tool Safety Warnings– Electrical
safety
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is
unavoidable, use a residual current device(RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
General Power Tool Safety Warnings– Personal
safety
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situation.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe
injury within a fraction of a second.
4 EN
cordless polisher PPOS 10-20V
General Power Tool Safety Warnings– Power tool
use and care
Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or
remove the battery pack, if detachable, from the power
tool before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
General Power Tool Safety Warnings– Battery tool
use and care
Recharge only with charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designed battery
packs. Use of any other battery packs may create a risk of
injury and fire.
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 130°C may cause explosion.
Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outsides the specified range may damage
the battery and increase the risk of fire.
General Power Tool Safety Warnings– Service
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Never service damaged battery pack. Service of battery
packs should only be performed by the manufacturer or
authorized service providers.
EN 5
cordless polisher PPOS 10-20V
Device-specific safety warnings for polishing
machines
Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
Hold onto the power tool with both hands. Position
your arms and your body in a way that allows you to
have the greatest control possible in order to absorb
kickback forces and reaction torques at high rotational
speeds.
Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may
grab the surface and pull the power tool out of your
control.
Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory could
snag your clothing and entangle the accessory in your
clothing.
Use special care when working corners and sharp
edges. Avoid the accessory bouncing or getting stuck
in a corner. The result would be a loss of control or
kickback.
Do not position your hand in the area next to the
rotating polishing wheel. In the event of a loss of control
or kickback, the rotating polishing wheel can hit your hand
and cause injuries.
Make sure that the polishing bonnet is well attached
on the polishing disc. A loose polishing bonnet can slip
from the polishing disc, get entangled with your hand and
cause injuries.
Only switch on the polishing machine once the
polishing disc completely rests on the area to be
polished.
Do not use abrasives. Abrasives can damage the paint.
Dust particles hazardous to health can be
released during dry polishing. Always wear a
suitable dust mask to protect you from inhaling dust
particles.
Safety Warnings Specific for Polishing Operations
Make sure that no loose parts of the polishing bonnet, in
particular its attachment strings, spring freely. Clamp the
attachment strings or cut them to length. Loose and spinning
attachment strings can entangle your fingers or snag on the
workpiece.
Intended use
Only use the device PPOS 10-20V:
for treating and refurbishing cars, boats, caravans,
motorcycles, floors or furniture.
for polishing, waxing or dewaxing painted or chromium-
plated areas.
We recommend using the power tool with original Trotec
accessories.
Foreseeable misuse
The device is not suitable for grinding, sanding, wire brushing or
working with cutting wheels.
Any other use than the one described in the chapter "Intended
use" is regarded as reasonably foreseeable misuse.
Personnel qualifications
People who use this device must:
have read and understood the instructions, especially the
Safety chapter.
6 EN
cordless polisher PPOS 10-20V
Personal protective equipment
Wear eye protection.
With it you protect your eyes from splintering, falling
and flying pieces which could cause injuries.
Wear a protective mask.
It saves you from inhaling harmful dusts generated
when processing workpieces.
Residual risks
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket and the battery from the device!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Warning of explosive substances
Do not expose the battery to temperatures above
45°C! Do not let the battery come into contact with
water or fire! Avoid direct sunlight and moisture. There
is a risk of explosion!
Warning of hot surface
Some parts of this product can become very hot and
cause burns. Particular attention has to be given where
children and vulnerable people are present!
Warning
Toxic dusts!
The harmful / toxic dusts produced during operation
pose of risk to the health of the operator and persons
in the vicinity.
Wear eye protection and a dust mask!
Warning
Do not process materials containing asbestos.
Asbestos is considered carcinogenic.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Caution
Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.
Caution
Keep a sufficient distance from heat sources.
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
EN 7
cordless polisher PPOS 10-20V
Information about the device
Device description
The device PPOS 10-20V is suited for treating and refurbishing
cars, boats, caravans, motorcycles, floors, furniture and other
painted surfaces.
The device operates at an idle speed of 3000min-1. The large
polishing disc with Ø245mm provides for treating large
surfaces.
The supplied cloth polishing bonnet is ideally suited for applying
polishing agent, the synthetic fibre polishing bonnet serves for
polishing or dewaxing surfaces.
No polishing marks will occur thanks to eccentric motion.
The device is equipped with two handles for maximum surface
control. It allows for an even pressure distribution.
The battery comes with its own battery level indication. As a
result you can check the current charging status without having
to connect it to the device.
Device depiction
1
2
3
2
12
4
5
11
6
10
9
7
8
No. Designation
1On/off switch
2Handle
3Polishing disc
4Quick charger
5Red battery LED (battery charging)
6Battery
7Cloth polishing bonnet
8Synthetic fibre polishing bonnet
9Battery level indication
10 Release button
11 Green battery LED (quick charger ready for operation)
12 Battery holder
Scope of delivery
1x Cordless polisher PPOS 10-20V
1 x Rechargeable battery
1x Quick charger
1x Cloth polishing bonnet
1x Synthetic fibre polishing bonnet
1x Manual
8 EN
cordless polisher PPOS 10-20V
Technical data
Parameter Value
Model PPOS10-20V
Nominal voltage 20V
Idle speed 3000min-1
Diameter of polishing disc 245mm
Weight 2.0kg
Battery Multiflex20 – 2.0 DC
Type Li-ion
Nominal voltage 20 V
Capacity 2Ah
Quick charger Multiflex20 – 2.0 AC
Input
Nominal voltage 230 - 240V / 50Hz
Power input 65W
Output
Nominal voltage 21.5V
Charging current 2.4A
Fusing 3.15A (slow-blowing)
Charging time 1 h
Protection class II /
Vibration information according to EN62841
Vibration emission value ah9.15m/s2
Uncertainty K 1.5m/s2
Sound values according to EN62841
Sound pressure level LpA 66.4dB(A)
Sound power LWA 77.4dB(A)
Uncertainty K 3 dB
Information on noise and vibration:
The specified total vibration and noise emission values
were measured by means of a test procedure standardized
in EN62841 and can be consulted for the comparison of
one power tool with another.
The specified total vibration and noise emission values
can also be used for preliminary load assessment.
Caution
Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.
The actual vibration and noise emission may differ from
the stated values during operation of the power tool. This
depends on how the power tool is used and especially on
the type of workpiece being processed. Try to keep the
vibration load to a minimum. Exemplary measures for
reducing the vibration load include wearing gloves during
operation of the tool and the limitation of working hours.
All parts of an operating cycle must be considered for this
(e.g. times at which the power tool is switched off and
times when it is switched on but runs without load).
EN 9
cordless polisher PPOS 10-20V
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, observe the following:
Switch off the device.
Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
Allow the device to cool down.
Remove the battery from the device.
Remove the polishing bonnet from the device.
The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:
The user may transport the batteries by road without any
additional requirements.
If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.
Only ship batteries if their housing is undamaged.
Mask open terminals with tape and pack the battery in
a way that it cannot move inside the packaging.
Please also observe any other national regulations.
Storage
Before storing the device, proceed as follows:
Switch off the device.
Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
Allow the device to cool down.
Remove the battery from the device.
Remove the polishing bonnet from the polishing disc.
Clean the device as described in the Maintenance chapter.
Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.
When the device is not being used, observe the following
storage conditions:
dry and protected from frost and heat
Ambient temperature below 45°C
protected from dust and direct sunlight
Store the device with the polishing disc facing upwards in
order for the polishing disc to maintain its shape.
Start-up
Unpacking the device
Take the device and the accessories out of the packaging.
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
Check the contents for completeness and look for
damages.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Dispose of the packaging material according to the
national regulations.
10 EN
cordless polisher PPOS 10-20V
Charging the battery
Note
The battery can be damaged in case of improper
charging.
Remove the charger's mains plug before inserting or
removing the battery.
Never charge the battery at ambient temperatures
below 10°C or above 40°C.
The battery is partially charged upon delivery to avoid damage
to the battery caused by a deep discharge.
Prior to initial start-up and when the battery is low (only the red
LED in the battery level indication(9) is illuminated), the battery
should be charged. To do so, please proceed as follows:
1. Slide the battery(6) onto the quick charger(4) upside
down until it locks in place.
1 h
6
4
11
5
9
2. Insert the mains plug of the quick charger(4) into a
properly fused mains socket.
ðThe red battery LED(5) lights up.
ðCharging requires approx. one hour.
3. Wait until the red battery LED(5) goes off and the green
battery LED(11) lights up.
ðThe battery(6) is fully charged.
4. Hold onto the mains plug while pulling the power cable of
the quick charger(4) out of the mains socket.
ðThe battery(6) and the quick charger(4) may have
become warm during charging.
Allow the battery(6) to cool down to room temperature.
5. Take the battery(6) out of the quick charger(4) by
pressing and holding the release button(10) and pulling
the battery(6) off the quick charger(4).
Inserting the battery
1. Slide the battery(6) onto the device until it locks in place.
6
Removing the battery
1. Detach the battery(6) from the device by pressing and
holding the unlocking button(10, I.) and pulling the battery
off the device(II.).
10
6
2. If required, charge the battery(6) as described in the
section Charging the battery.
EN 11
cordless polisher PPOS 10-20V
Checking the battery charging status
The battery comes with an integrated battery level indication.
The battery status is displayed as follows by the three LEDs of
the battery level indication(9):
LED colour Meaning
Green – Orange – Red maximum charge/ power
Orange – Red medium charge/ power
Red weak charge – Recharge the
battery.
1. Press on the battery icon(13) on the battery(6).
ðYou can read the battery status from the battery level
indication(9).
13
9
Placing the polishing bonnet on the device
1. Remove the battery from the device.
2. Turn the bottom of the device up.
3. Pull the polishing bonnet(7 or 8) over the polishing
disc(3).
3
7/8
Operation
Tips and notes on handling the polishing machine
General information:
Make sure that the surface to be treated and the polishing
bonnets are free from dirt. Dirt particles can cause
scratches on the surface.
Slowly guide the device along the surface to be polished.
Do not apply grinding pressure.
If there are any areas difficult to access, remove the
polishing bonnet from the polishing disc and treat the
areas manually.
Make sure that the paint to be treated has been thoroughly
cleaned and is completely dry. Heavily oxidised paint
requires a special cleaning agent.
Only use high-quality products for waxing and polishing
and observe the process information of the manufacturer
specified on the packaging.
Applying the polish:
Use the supplied cloth polishing bonnet for applying the
polish.
Evenly distribute the polishing agent all the way to the
edge of the cloth polishing bonnet.
Dab the cloth polishing bonnet on several spots of the
surface to be polished. Once more, any excess polishing
agent will distribute in the cloth polishing bonnet and on
the surface to be polished.
Avoid using too much polishing agent. Later on, this will
only make it more difficult to remove the layer of the
polishing agent on the paint and does not improve the
result.
Make sure to apply the polishing agent evenly to obtain an
equally thin coating without any left-out spots.
If you apply the polishing agent on a vehicle, treat all even
and large surfaces (e.g. bonnet of the car, boot lid and
roof) first. Afterwards, treat the smaller areas such as
doors and car wings.
Polishing surfaces:
Use the supplied synthetic fibre polishing bonnet for
polishing.
Prior to polishing, make sure that the polishing agent has
lightly dried on the entire surface.
Treat the surfaces in the same order as you applied the
polishing agent before. Treat even and large areas first.
Then, treat smaller areas.
12 EN
cordless polisher PPOS 10-20V
Switching the device on and off
Wear your personal protective equipment when working with
the device.
1. Take the device into both hands by holding it on the
handles.
2. Place the polishing machine on the area to be treated.
3. Switch the device on by setting the on/off switch (1) to
position I.
1
4. Switch the device off by setting the on/off switch(1) to
positionO. Only then remove the device from the surface
to be treated.
1
Shutdown
Switch off the device.
If required, allow the device to cool down.
Remove the battery from the device (see Start-up chapter).
Remove the polishing bonnet from the polishing disc.
Clean the device according to the Maintenance chapter.
Store the device according to the Storage chapter.
Available accessories
Warning
Only use accessories and additional equipment
specified in the instructions.
Using insertion tools or accessories other than those
specified in the instructions may cause a risk of injury.
Designation Article number
Spare battery Multiflex20-2.0DC 6.200.000.303
Spare battery Multiflex20-4.0DC 6.200.000.320
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Light smoke or odour is emitted during the first use:
This is not a fault. These phenomena disappear after a
brief runtime.
The battery does not charge:
Check whether the battery is inserted correctly in the quick
charger.
Slide the battery into the quick charger in a way that the
battery terminals engage in the quick charger. The battery
must lock in place in the quick charger.
Check the power connection.
Check the power cable and mains plug for damage.
Check the on-site fusing.
Check the quick charger for damage. If the quick charger
is damaged, stop using it. Contact the Trotec customer
service.
Check the battery terminals for dirt. Remove any dirt.
The battery might be defective and have to be replaced.
Only use batteries of the same type.
EN 13
cordless polisher PPOS 10-20V
The device does not start:
The battery power might be too low. Recharge the battery.
Check whether the battery is correctly connected to the
device.
Slide the battery onto the device in a way that the battery
terminals engage. The battery must lock in place in the
device.
Check the battery terminals for dirt. Remove any dirt.
Info
Wait for at least 10 minutes before switching the
device back on.
The motor is running but polishing the surface does not
work
Check whether you chose the appropriate polishing bonnet
for your current working step. Use the cloth polishing
bonnet for applying the polishing agent. Use the synthetic
fibre polishing bonnet for polishing the surfaces.
Check whether the polishing agent has lightly dried on the
entire surface. If the polishing agent is still wet, it will be
smudged by the synthetic fibre polishing bonnet.
Check whether you may have applied too much polishing
agent. Excess polishing agent will only make it more
difficult to remove the layer of the polishing agent on the
paint and does not improve the result.
The device becomes hot:
Keep the venting slots clear to prevent the motor from
overheating.
Info
Wait for at least 10 minutes before switching the
device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug or the battery with wet or
damp hands.
Switch off the device.
Allow the device to cool down completely.
Remove the battery from the device.
Warning of electrical voltage
Maintenance tasks which require the housing to be
opened must only be carried out by authorised
specialist companies or by Trotec.
Notes on maintenance
Inside the device, there are no parts that need to be maintained
or lubricated by the user.
Cleaning
The device should be cleaned before and after each use.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Clean the device with a soft, damp and lint-free cloth.
Make sure that no moisture enters the housing. Protect
electrical components from moisture. Do not use any
aggressive cleaning agents such as cleaning sprays,
solvents, alcohol-based or abrasive cleaners to dampen
the cloth.
Dry the device with a soft, lint-free cloth.
Keep the connecting terminals on the device and charger
clean.
Cleaning the polishing bonnets
Only wash the polishing bonnets by hand and allow to air
dry.
Remove the polishing bonnet if you do not use it and store
the device with the polishing disc facing upwards in order
for the polishing disc to dry and to maintain its shape.
14 EN
cordless polisher PPOS 10-20V
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website https://de.trotec.com/shop/.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
Li-Ion
In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.
Declaration of conformity
The text below sets out the contents of the declaration of
conformity. The signed declaration of conformity can be found
at https://hub.trotec.com/?id=44253.
Declaration of conformity
in accordance with the ECMachinery Directive 2006/42/EC, AnnexII, Part1,
SectionA
Herewith, we– TrotecGmbH– declare that the machinery
designated below was developed, constructed and produced in
compliance with the requirements of the ECMachinery
Directive in the version 2006/42/EC.
Product model/ Product: PPOS 10-20V
Product type: cordless polisher
Year of manufacture as of: 2020
Relevant EU directives:
2012/19/EU: 24 July 2012
2014/30/EU: 29March 2014
Applied harmonised standards:
EN ISO 12100:2010
ENISO 20607:2019
EN 62841-1:2015
EN62841-2-4:2014
Applied national standards and technical specifications:
Regulation (EG) 1907/2006
AfPS GS 2014:01 PAK
EN 55014-1:2017
EN 55014-2:2015
Manufacturer and name of the authorised representative of
the technical documentation:
Trotec GmbH
Grebbener Straße 7, D-52525 Heinsberg
Phone: +49 2452 962-400
E-mail: info@trotec.de
Place and date of issue:
Heinsberg, 26.01.2020
Detlef von der Lieck, Managing Director
Trotec GmbH
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
info@trotec.com
www.trotec.com
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PPOS10-20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PPOS10-20V in the language / languages: English as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PPOS10-20V

Trotec PPOS10-20V User Manual - German - 15 pages

Trotec PPOS10-20V User Manual - Dutch - 15 pages

Trotec PPOS10-20V User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info