753363
10
Zoom out
Zoom in
Previous page
1/21
Next page
10 EN
cordless multi-function tool PMTS 10-20V
Information on noise and vibration:
The specified total vibration and noise emission values
were measured by means of a test procedure standardized
in EN62841 and can be consulted for the comparison of
one power tool with another.
The specified total vibration and noise emission values
can also be used for preliminary load assessment.
Caution
Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.
The actual vibration and noise emission may differ from
the stated values during operation of the power tool. This
depends on how the power tool is used and especially on
the type of workpiece being processed. Try to keep the
vibration load to a minimum. Exemplary measures for
reducing the vibration load include wearing gloves during
operation of the tool and the limitation of working hours.
All parts of an operating cycle must be considered for this
(e.g. times at which the power tool is switched off and
times when it is switched on but runs without load).
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
For transporting the device, use the transport case included in
the scope of delivery in order to protect the device from external
influences.
Before transporting the device, observe the following:
Switch off the device.
Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
Allow the device to cool down.
Remove the battery from the device.
Remove the tool from the tool holder.
If attached, disconnect the dust extraction system from the
device.
The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:
The user may transport the batteries by road without any
additional requirements.
If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.
Only ship batteries if their housing is undamaged.
Mask open terminals with tape and pack the battery in
a way that it cannot move inside the packaging.
Please also observe any other national regulations.
Storage
Before storing the device, proceed as follows:
Switch off the device.
Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
Allow the device to cool down.
Remove the battery from the device.
Remove the tool from the tool holder.
If attached, disconnect the dust extraction system from the
device.
Clean the device as described in the Maintenance chapter.
For storing the device, use the transport case included in
the scope of delivery in order to protect the device from
external influences.
Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.
When the device is not being used, observe the following
storage conditions:
Dry and protected from frost and heat
Ambient temperature below 45°C
Protected from dust and direct sunlight inside the transport
case
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PMTS10-20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PMTS10-20V in the language / languages: English as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PMTS10-20V

Trotec PMTS10-20V User Manual - German - 22 pages

Trotec PMTS10-20V User Manual - Dutch - 22 pages

Trotec PMTS10-20V User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info