689479
18
Zoom out
Zoom in
Previous page
1/22
Next page
17 EN
cordless multi-function tool PMTS 10-12V
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Slight smoke or odour are emitted during first use:
This is not a fault. These phenomena disappear after a
brief runtime.
The battery does not charge:
Check whether the battery is inserted correctly in the quick
charger.
Slide the battery into the quick charger in a way that the
battery terminals engage in the quick charger. The battery
must lock in place in the quick charger.
Check the power connection.
Check the power cable and mains plug for damages.
Check the on-site fusing.
Check the quick charger for damages. Should the quick
charger be damaged, stop using it. Contact the Trotec
customer service.
Check the battery terminals for dirt. Remove any dirt.
The battery might be defective and have to be replaced.
Only use batteries of the same type.
The device does not start:
The battery power might be too low. Recharge the battery.
Check whether the battery is correctly connected to the
device.
Slide the battery onto the device in a way that the battery
terminals engage. The battery must lock in place in the
device.
Check the battery terminals for dirt. Remove any dirt.
Info
Wait for at least 10 minutes before switching the
device back on.
The tool is loose:
Make sure that the tool is firmly locked in place in the
designated recesses of the tool holder.
Make sure that the clamping screw at the tool holder is
tightened properly.
Make sure that the tool release lever is folded back
completely.
The saw blade experiences difficulties plunge-cutting the
material to be processed or the sawing/grinding
performance is insufficient:
Check the set oscillation rate, it must be suitable for both
the tool and the material.
To select a higher oscillation rate, turn up the setting
wheel for oscillation rate selection.
If the saw blade is worn, replace it with a new one.
Check whether the chosen tool is suitable for the material
to be processed.
The device becomes hot:
Make sure not to exert too much pressure on the device
during grinding.
Select a low oscillation rate by turn down the setting wheel
for oscillation rate selection(4).
Check whether the tool is suitable for the tasks to be
carried out.
Keep the venting slots clear to prevent the motor from
overheating.
Wait for at least 10 minutes before switching the device
back on.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PMTS10 - 12V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PMTS10 - 12V in the language / languages: English as an attachment in your email.

The manual is 1,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PMTS10 - 12V

Trotec PMTS10 - 12V User Manual - German - 23 pages

Trotec PMTS10 - 12V User Manual - Dutch - 23 pages

Trotec PMTS10 - 12V User Manual - French - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info