753285
5
Zoom out
Zoom in
Previous page
1/18
Next page
EN 5
Impact drill PHDS 10-230V
Before switching on the power tool, ensure that the
insertion tool can move freely. If the device is switched
on with a jammed insertion tool, the resulting forces can
be extreme causing the device to kick out sideways.
Immediately switch off the power tool if the insertion
tool blocks. The power tool can lash out to the side owing
to the forces that build up consequently.
Regularly check the drill chuck for wear or damage.
Only start a percussive power tool while holding it
against a workpiece (wall, ceiling, etc.).
Wait until the power tool has come to a standstill,
before putting it down.
Processing metal creates flying sparks. Make sure that
nobody's safety is jeopardized and that there are no
combustible materials near the working area. Fire hazard!
Avoid drilling in lead paint or other harmful materials.
Always keep the power cable behind the device.
Make sure that the venting slots are not covered
during operation. Do not insert any objects into the
venting slots.
The device must always be clean, dry and free from oil
or greases.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
the workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
not apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal injury.
Intended use
Only use the device PHDS 10-230V:
for screwing in and loosening screws,
for drilling in wood, plastic, ceramic and metal,
for impact drilling in masonry, bricks and stone,
whilst adhering to the technical data (see operating manual).
We recommend using the power tool with original Trotec
accessories.
Foreseeable misuse
The device is not intended for drilling in natural stone.
Any other use than the one described in chapter "Intended use"
is regarded as reasonably foreseeable misuse.
Personnel qualifications
People who use this device must:
have read and understood the instructions, especially the
Safety chapter.
Symbols on the device
Symbols Meaning
This symbol located on the device indicates
that it is prohibited to press the spindle lock
during operation. Pressing the spindle lock
during operation can damage the motor
and/ or gear.
Personal protective equipment
Wear protective headgear.
With it you protect your head from splintering, falling
and flying pieces which could cause injuries.
Wear hearing protection.
Excessive noise can lead to hearing loss.
Wear eye protection.
With it you protect your eyes from splintering, falling
and flying pieces which could cause injuries.
Wear a protective mask.
It saves you from inhaling harmful dusts generated
when processing workpieces.
Wear protective gloves.
They protect your hands from burns, crushing injuries
and skin abrasions.
Wear tight-fitting protective clothing.
This protects you from the draw-in and entanglement
hazard posed by rotating parts.
Wear safety boots.
They protect your feet from splintering, falling and
flying pieces which could cause injuries.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PHDS 10-230V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PHDS 10-230V in the language / languages: English as an attachment in your email.

The manual is 3,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PHDS 10-230V

Trotec PHDS 10-230V User Manual - German - 20 pages

Trotec PHDS 10-230V User Manual - Dutch - 20 pages

Trotec PHDS 10-230V User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info