753908
15
Zoom out
Zoom in
Previous page
1/20
Next page
EN 15
mini cordless portable circular saw PCSS 05-20V
Operation
Tips and notes on handling the circular saw
General information:
Keep the venting slots clear to prevent the motor from
overheating.
Only use intact, flawless saw blades. Saw blades can be
damaged by shocks or impacts. Bent, blunt or otherwise
damaged saw blades could break. The sawing
performance and cutting quality essentially depend on the
saw blade's condition and the shape of the teeth.
Check the saw blade for correct fit before every
application.
Before every application, make sure that you have selected
the correct saw blade for the intended use.
Before every application, check whether you need a dust
bag or dust extraction system.
Harmful dusts are produced when processing wood,
particularly beech and oak. Beech and oak dust is
considered carcinogenic, especially in combination with
certain wood treatment additives such as chromate or
wood preservatives. Wear a protective mask.
Dusts from materials containing leaded paint or
minerals can be harmful to health. Wear a protective
mask.
Long, spiral chips are produced when processing
spruce.
The falling part of the workpiece should be located on the
right-hand side of the power tool so that the larger part of
the workpiece remains in full contact with the supporting
table or similar.
Guide the power tool by pushing slightly and evenly in the
cutting direction. Pushing too hard reduces the blade life
and can damage the power tool.
If you are sawing along a drawn line, guide the power tool
along the respective notch.
Tear-out of the edges cut into sensitive surfaces (e.g.
plasterboard or coated chipboard) can be prevented by
covering the cutting edges with masking tape. In this case,
the cutting line can also be drawn on the masking tape to
protect the workpiece surface.
Non-coated saw blades can be protected against corrosion
by applying a thin layer of acid-free oil. Remove any oil
before starting to saw to prevent oil residues from reaching
the wood.
When sawing lightweight construction materials, observe
the legal regulations and recommendations of the material
manufacturers.
Sawing wood:
Before sawing wood, chipboards, building materials etc.,
check the above for foreign objects, e.g. nails, screws or
similar. If required, remove the foreign objects or use a
suitable, sharp saw blade.
The choice of the saw blade depends on the type of
application (longitudinal or cross cuts) as well as the type
and quality of wood.
If the saw blade gets jammed in the workpiece, switch off
the power tool immediately. The sawing gap should be
slightly widened with a suitable tool so that you can pull
out the power tool.
Switch on the power tool and guide it towards the
workpiece to be processed. Place the guide shoe on the
surface of the workpiece. Process the workpiece with an
even forward motion and contact pressure. After
completing the sawing operation, switch off the power
tool.
Sawing non-ferrous metals:
Metal dusts can be harmful to health. Wear a protective
mask.
Only use a sharp saw blade suitable for non-ferrous
metals. This guarantees a clean cut and prevents the saw
blade from getting jammed.
Only hold the power tool against the workpiece when the
tool is switched on and running. Start sawing carefully and
with little forward motion. Continue sawing with little
forward motion and without interrupting.
When sawing narrow profiles, you should start on the
narrow side. When sawing U-profiles, you should start on
the open side. Long profiles should be supported to
prevent the saw blade from getting jammed and thus to
avoid the risk of a kickback.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PCSS 05-20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PCSS 05-20V in the language / languages: English as an attachment in your email.

The manual is 4,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PCSS 05-20V

Trotec PCSS 05-20V User Manual - German - 21 pages

Trotec PCSS 05-20V User Manual - Dutch - 20 pages

Trotec PCSS 05-20V User Manual - French - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info