753913
20
Zoom out
Zoom in
Previous page
1/23
Next page
19 EN
cordless angle grinder PAGS 20-115
The guard is loose:
Make sure that the coded projections are firmly locked in
place in the designated groove.
Make sure that the locking lever is folded in completely.
If necessary, tighten the adjusting screw.
The cutting disc does not move although the motor is
running:
Make sure that the clamping nut is firmly tightened, see
chapter Tool change.
Make sure that there is no workpiece debris blocking the
drive. Remove the blockages, if any.
Make sure that the cutting disc is not jammed in the
workpiece.
The motor slows down:
Check whether the device is overloaded by the workpiece.
Reduce the pressure applied on the workpiece.
Check whether the workpiece is suitable for the tasks to
be carried out.
The cutting disc experiences difficulties penetrating the
material to be processed or the cutting performance is
insufficient:
Check whether the chosen cutting disc is suitable for the
material to be processed.
If the cutting disc is worn, replace it with a new one.
The device becomes hot:
Check whether the cutting disc is suitable for the tasks to
be carried out.
Make sure not to exert too much pressure on the device
during operation.
Keep the venting slots clear to prevent the motor from
overheating.
Wait for 10minutes before switching the device back on.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug or the battery with wet or
damp hands.
Switch off the device.
Allow the device to cool down completely.
Remove the battery from the device.
Warning of electrical voltage
Maintenance tasks which require the housing to be
opened must only be carried out by authorised
specialist companies or by Trotec.
Notes on maintenance
Inside the device, there are no parts that need to be maintained
or lubricated by the user.
Cleaning
The device should be cleaned before and after each use.
Note
The device does not have to be lubricated after
cleaning.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Clean the device with a soft, damp and lint-free cloth.
Ensure that no moisture enters the housing. Protect
electrical components from moisture. Do not use any
aggressive cleaning agents such as cleaning sprays,
solvents, alcohol-based or abrasive cleaners to dampen
the cloth.
Dry the device with a soft, lint-free cloth.
Remove dust from inside the guard, from the mounting
flange and from the clamping nut.
Keep the connecting terminals on the device and charger
clean.
Keep the connecting terminals on the battery pack clean.
Keep the ventilation openings free from dust deposits to
prevent overheating of the motor.
For maintenance of the cutting disc, see chapter Tool
change.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PAGS20-115 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PAGS20-115 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PAGS20-115

Trotec PAGS20-115 User Manual - German - 25 pages

Trotec PAGS20-115 User Manual - Dutch - 25 pages

Trotec PAGS20-115 User Manual - French - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info