728000
18
Zoom out
Zoom in
Previous page
1/21
Next page
TRT-BA-PAE26-TC-002-EN
PAE 26
EN
OPERATING MANUAL
AIR COOLER
1 EN
air cooler PAE 26
Table of contents
Notes regarding the operating manual.................................1
Safety .....................................................................................1
Information about the device................................................3
Transport and storage...........................................................4
Assembly and start-up..........................................................5
Operation ...............................................................................9
Available accessories..........................................................12
Errors and faults..................................................................13
Maintenance ........................................................................14
Technical annex...................................................................18
Disposal ...............................................................................18
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
PAE 26
https://hub.trotec.com/?id=41938
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
Do not use the device in potentially explosive rooms.
Do not use the device in aggressive atmosphere.
Set the device up in an upright and stable position.
Let the device dry out after a wet clean. Do not operate it
when wet.
Do not use the device with wet or damp hands.
Do not expose the device to directly squirting water.
Never insert any objects or limbs into the device.
Do not cover or transport the device during operation.
Do not sit on the device.
This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
EN 2
air cooler PAE 26
Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
The electrical connection must correspond to the
specifications in chapter Technical data.
Insert the mains plug into a properly secured mains
socket.
Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!
When positioning the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
data chapter.
Make sure that the air inlet and outlet are not obstructed.
Make sure that the suction side is kept free of dirt and
loose objects.
Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
Only transport the device in an upright position with an
emptied water tank.
Empty the water tank before transport and storage. Do not
drink the water. Health hazard!
Only fill the water tank with fresh drinking water, ice cubes
made of fresh drinking water and/ or suitable ice packs.
Ice packs are not toys. Keep away from children and
animals.
Never open an ice pack. The liquid inside the ice packs
can be harmful to health.
Do not eat the ice that may form on the ice packs. Health
hazard!
Intended use
Only use the device for cooling the air in interior spaces while
adhering to and following the technical data.
Intended use comprises cooling the air in:
living spaces
museums
warehouses and archives
libraries
call centres and computer rooms
Improper use
Do not place the device on wet or flooded ground.
Do not place any objects, e.g. clothing, on the device.
Do not use the device outdoors.
Any unauthorised modifications, alterations or structural
changes to the device are forbidden.
Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability
and guarantee null and void.
Personnel qualifications
People who use this device must:
be aware of the dangers that occur when working with
electric devices in damp areas.
have read and understood the operating manual, especially
the Safety chapter.
Maintenance tasks which require the housing to be opened
must only be carried out by specialist electrical companies or by
Trotec.
3 EN
air cooler PAE 26
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning
The liquid inside the ice packs can be harmful to
health!
If the liquid was swallowed, immediately seek medical
attention.
If the liquid came into contact with your eyes, rinse
with water and immediately consult an
ophthalmologist.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Note
Do not operate the device without an inserted air filter!
Without the air filter, the inside of the device will be
heavily contaminated. This could reduce the
performance and result in damage to the device.
Behaviour in the event of an emergency
1. Switch off the device.
2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power
cable out of the mains socket.
3. Do not reconnect a defective device to the mains.
Information about the device
Description of the device
The air cooler lowers the room temperature to a comfortable
degree by evaporation-based cooling.
The device is filled with cold water or optionally with ice cubes
and/or ice packs in order to cool down the incoming warm air
at the evaporation filter and to blow out the cold air thus
generated via the fan.
Besides its cooling function, the device can also be used for air
freshening: thanks to an integrated air filter and the evaporation
filter's honeycomb structure, the sucked-in air is filtered and
humidified.
The fan speed can be set to three stages.
The discharge direction of the cooled air can be manually
adjusted via the ventilation flaps as well as via the optionally
selectable automatic swing mode.
The device has a night mode enabling ultra-silent operation at
bedtime.
The device can be operated via the control panel at the device
or via the infrared remote control.
Moreover, using the timer function, the device can be switched
off automatically with time delay.
The device is equipped with an overheating protection that
switches off the air cooler in case of overheating.
EN 4
air cooler PAE 26
Device depiction
1
2
3
4
5
15
6
11
12
13
14
9
7
10
8
No. Designation
1 Transport handle
2 Control panel
3 Air outlet with adjustable ventilation flaps and air
flaps for swing function
4 Water level indicator
5 Wheels with parking brake
6 Power cable holder
7 Honeycomb filter
8 Ice packs
9 Remote control
10 Air filter
11 Water tank with filling level indicator
12 Cover for water tank
13 Air inlet with air filter and honeycomb filter
14 Compartment for the remote control
15 Remote control receiver
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
To make the device easier to transport, it is fitted with wheels.
To make the device easier to transport, it is fitted with a carry
handle.
Before transporting the device, observe the following:
Switch the device off.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Empty the water tank.
Do not use the power cable to drag the device.
Release the brakes at the castors.
Only wheel the device on a level and smooth surface.
After transporting the device, observe the following:
Set up the device in an upright position after transport.
5 EN
air cooler PAE 26
Storage
Before storing the device, observe the following:
Empty and clean the water tank prior to storage (see
chapter Maintenance).
Allow the honeycomb filter to dry prior to storage.
Otherwise the device may distribute a musty smell after
restart.
When the device is not being used, observe the following
storage conditions:
dry and protected from frost and heat
in an upright position where it is protected from dust and
direct sunlight
with a cover to protect it from invasive dust if necessary
Place no further devices or objects on top of the device to
prevent it from being damaged.
Remove batteries from the remote control.
Assembly and start-up
Scope of delivery
1x Device
1 x Remote control
1 x Battery for the remote control
1x Honeycomb filter
1x Air filter
4x Wheel
2 x Ice pack
1x Manual
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Start-up
When positioning the device, observe the minimum distance
from walls or other objects as described in the Technical data
chapter.
A
B
C
C
D
Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
Set the device up in an upright and stable position.
Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
Make sure that extension cables are completely unrolled.
Make sure that no curtains or other objects interfere with
the air flow.
Prior to initial start-up, insert the batteries in the remote control.
EN 6
air cooler PAE 26
Mounting the wheels
To ensure simple transportation and a stable position, the
supplied wheels must be mounted. To do so, please proceed as
follows:
Note
When mounting the wheels, make sure that the filled
water tank is not located inside the device.
1. Place the device on its side and insert a roller. Repeat this
step for the 3remaining wheels.
ð Please note that the wheels equipped with a parking
brake ought to be positioned at the rear of the device.
To facilitate easy transport, release the parking brakes.
To ensure a firmly fixed position, apply the parking brakes.
Filling the water tank
The device requires fresh drinking water for air cooling.
Note
Fill the device with fresh drinking water only. The
water temperature must not exceed 40°C.
Info
If possible, change the water on a daily basis to
prevent bacterial growth.
Observe the following when using the ice packs:
Put the ice packs into a freezer for at least 4hours before
use.
The water tank(11) should be filled with water before
inserting the ice packs.
Only place the ice packs into the designated compartment
in the water tank, otherwise the pump will not function
properly.
Info
When using ice packs at high outside temperatures,
condensation may form at the water tank and drip onto
the floor.
7 EN
air cooler PAE 26
1. Disconnect the device from the mains before refilling water
or putting ice packs into the device.
2. Remove the water tank(11) from the device.
3. Fill the water tank(11) with fresh drinking water only.
Optionally, you can add ice cubes made of drinking water
for additional cooling.
ð Observe the minimum and maximum filling level at the
filling level indicator.
The water tank must be filled up to minimum filling level
to enable pump operation.
4. If required, put the ice packs into the compartment inside
the water tank to achieve an enhanced cooling effect.
5. Refit the water tank into the device.
6. Make sure that the device is neither damp nor wet on the
outside. Otherwise wipe it dry.
EN 8
air cooler PAE 26
Inserting honeycomb filter and air filter
Note
When set to air cooling mode, the device should not be
operated without the honeycomb filter, otherwise
cooling will not work.
Note
Do not operate the device without an inserted air filter!
Without the air filter, the inside of the device will be
heavily contaminated. This could reduce the
performance and result in damage to the device.
Make sure that both the honeycomb and the air filter are
installed before switching the device on.
Opening the ventilation flaps
Prior to switching the device on, adjust the ventilation flaps
at the air outlet.
Connecting the power cable
Insert the mains plug into a properly secured mains
socket.
Info
An acoustic signal will be emitted; the device is now in
standby mode.
9 EN
air cooler PAE 26
Operation
Avoid open doors and windows.
Operating elements
16 17 18 19 20 21
22232425
26
2728
No. Designation Meaning
16 On / Off LED Illuminated during operation
17 Oscillation LED Illuminated when swing function
is activated
18 Hours LEDs Indication of the number of hours
of the activated timer(1 to 7h)
through a combination of the
symbols 1h, 2h and/or 4h
When added up, the illuminated
symbols indicate the desired
number of hours
19 Fan stage LEDs Fan speed indication is
illuminated:
Stage 1 = low
Stage 2 = medium
Stage 3 = high
20 Mode LEDs Indication of the selected
operating mode is illuminated:
ventilation
air freshening
night mode
21 Humidify LED Illuminated when air cooling mode
is activated
Flashes when water tank is empty
22 Humidify button Switching the air cooling mode on
or off
23 Mode button Selection button for ventilation, air
freshening and night mode
24 Speed button Setting the fan speed
No. Designation Meaning
25 Child lock indication Illuminated when the child lock is
active
26 Timer button Switching the timer on or off
1 h to 7 h
27 Oscillation button Switching the swing function on
or off
28 On / Off button Switching the device on or off
Switching the device on
Once you have completely installed the device as described in
the Start-up chapter, you can switch it on.
1. Press the On / Off button(28).
ð The device starts in air cooling, ventilation mode at fan
stage1. In case of initial start-up the swing function is also
activated.
ð The LEDs On/ Off(16), Oscillation(17), Humidify(21),
Ventilation(20) and Fan stage1(19) are illuminated.
Setting the operating mode
The device comes with the following operating modes:
air cooling
ventilation
air freshening
night mode
Air cooling
The air cooling mode can be switched on in addition during all
other operating modes.
During air cooling the pump is switched on and the water is
distributed over the honeycomb filter to cool the circulating air.
With an empty water tank the pump automatically switches off,
an acoustic alarm signal will be emitted and the Humidify
LED(21) flashes.
Please proceed as follows to activate air cooling:
1. Press the Humidify button(22).
ð The Humidify LED(21) is illuminated.
ð The pump starts.
2. Press the Speed button(24) to set the desired fan stage (1
to3).
3. Press the Humidify button(22) again to switch air cooling
off.
ð The Humidify LED(21) goes out.
ð The device continues to run in the previously selected
operating mode.
Note
When air cooling mode is activated, the water tank
must not be removed, otherwise the water from the
filter will drip down into the device.
EN 10
air cooler PAE 26
Ventilation
In ventilation mode, you can select all 3fan speeds manually.
Please proceed as follows to activate ventilation:
1. Press the Mode button(23) until the ventilation LED(20) is
illuminated.
2. To adjust the fan stage, press the Speed button(24) until
the LED for the desired fan stage(19) is illuminated.
Air freshening
In air freshening mode, the fan speed increases and decreases
alternately to generate a pleasant, natural air stream.
Please proceed as follows to activate air freshening:
1. Press the Mode button(23) until the Air freshening
LED(20) is illuminated. The fan stages are automatically
adjusted.
Activating night mode
Night mode can be activated in combination with the 3fan
stages and air cooling.
1. Press the Mode button(23) until the Night mode LED(20)
is illuminated. Also select the desired fan speed.
ð Fan stage1: The device runs in air freshening mode.
ð Fan stage2: The device operates in air freshening mode
and after 30minutes switches over to fan stage1.
ð Fan stage3: The device operates in air freshening mode
and after 30minutes switches over to fan stage2. When
another 30minutes have passed, the device automatically
switches over to fan stage1.
Info
If you activate air cooling, an alarm signal will be
emitted when the water tank is empty, even in night
mode.
Setting the timer
The function can be set in all operating modes.
The number of hours can be between 1 and 7 and can be
adjusted in increments of 1h.
Automatic switch-off
ü The device is switched on.
1. Press the Timer button(26) until the desired number of
hours is displayed as a combination of the different Hours
LEDs(18).
ð The timer setting equals the desired number of hours.
ð The device switches off automatically after the set number
of hours has elapsed.
Notes regarding automatic switch-off:
Pressing the On/ Off button(28) deactivates the automatic
switch-off function.
Remote control
All settings of the device can also be made using the remote
control included in the scope of delivery.
28
22
26
24
27
23
No. Designation Meaning
22 Humidify button Switching the air cooling mode on
or off
23 Mode button Selection button for ventilation, air
freshening and night mode
24 Speed button Setting the fan speed
26 Timer button Switching the timer on or off
1 h to 7 h
27 Oscillation button Switching the swing function on
or off
28 On/ Off button Switching the device on or off
Swing function
The swing function can be switched on in any operating mode if
required.
Behind the horizontal ventilation flaps, there are vertical air flaps
integrated in the device. By means of the swing function, these
air flaps are moved automatically and thus ensure continuous
air circulation.
1. Press the Oscillation button(27) to switch the swing
function on or off.
ð With activated swing function the OscillationLED(17) is
illuminated.
Memory function
If you switch the device back on after initial start-up, the
settings selected for the operating mode are saved. Any
activated timer will not be saved in the device.
11 EN
air cooler PAE 26
Child lock
The child lock serves to disable the operating elements and can
be activated in all operating modes.
With active child lock the device runs in the set operating mode,
but no adjustments can be made by actuating the buttons.
1. Simultaneously press and hold the buttons Speed(24) and
Timer(26) on the device for 3s to enable or disable the
child lock function.
ð If child lock is activated, only the On/ Off LED(16) will be
illuminated.
ð Upon actuation of a button, the LEDs for the selected
operating mode light up for approx. 10s.
Refilling water
An empty water tank is indicated by the device with an acoustic
signal and a flashing Humidify LED(21). In this case, the water
tank must be refilled.
Observe the following when using the ice packs:
Put the ice packs into a freezer for at least 4hours before
use.
The water tank(11) should be filled with water before
inserting the ice packs.
Only place the ice packs into the designated compartment
in the water tank, otherwise the pump will not function
properly.
Info
When using ice packs at high outside temperatures,
condensation may form at the water tank and drip onto
the floor.
1. Disconnect the device from the mains before refilling water
or putting ice packs into the device.
2. Remove the water tank(11) from the device.
3. Fill the water tank(11) with fresh drinking water only.
Optionally, you can add ice cubes made of drinking water
for additional cooling.
ð Observe the minimum and maximum filling level at the
filling level indicator.
The water tank must be filled up to minimum filling level
to enable pump operation.
4. If required, put the ice packs into the compartment inside
the water tank to achieve an enhanced cooling effect.
5. Refit the water tank into the device.
6. Make sure that the device is neither damp nor wet on the
outside. Otherwise wipe it dry.
EN 12
air cooler PAE 26
Auto stop function
After 24hours of continuous operation the device switches off
automatically.
Overheating protection
The device comes equipped with an overheating protection. It
serves to protect the air cooler from overheating.
Overheating might be caused by a dirty filter or an obstruction.
In case of overheating the device switches off automatically.
After the overheating protection has tripped, the device cannot
be put back into operation.
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Switch off the device.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Empty and clean the water tank (see chapter
Maintenance).
Clean the device according to the Maintenance chapter.
Store the device according to the Storage chapter.
Available accessories
Warning
Only use accessories and additional equipment
specified in the operating manual.
Using insertion tools or accessories other than those
specified in the operating manual may cause a risk of
injury.
Designation Article number
Evaporation filter PAE 26 7.710.000.854
13 EN
air cooler PAE 26
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damages.
Check the on-site fusing.
Check whether the overheating protection has tripped (see
chapter Operation).
Wait for 10minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device has automatically switched itself off:
Keep the air inlet clear to prevent the motor from
overheating.
Check whether the overheating protection has tripped (see
chapter Operation).
The device works with reduced or no capacity:
Check the position of the horizontal ventilation flaps. They
should be opened to the maximum.
Check the air filter for dirt. If necessary, clean or replace
the air filter.
Check the minimum distance to walls or other objects.
Position the device a little more in the room's centre if
required.
The device is running, but there is no air cooling or pump
operation:
Check whether air cooling mode is activated. The Humidify
LED(21) should be illuminated.
Check the filling level of the water tank (see chapter Filling
the water tank). The Humidify LED(21) should not flash.
Check whether there are any objects blocking the pump
inlet. Make sure that the pump inlet is not blocked.
In case the pump does not operate despite a correctly filled
water tank and activated air cooling mode, the pump might
be defective. Please contact the customer service.
Water is leaking:
Check the device for leaks.
Check the water tank for tight fit.
The water tank cannot be inserted
Check whether the mechanism for lowering the pump was
released. If the pump can be seen in the lower area, the
water tank is being blocked.
Push the pump up until the switch for lowering the
pump can be seen.
The swing function is not working:
The swing function motor might be defective. Please
contact the customer service.
The device is loud or vibrates:
Check whether the device is set up in a stable and upright
position.
The device does not respond to the infrared remote control:
Check whether the distance between remote control and
device is too large and reduce it if necessary.
Make sure there are no obstacles, such as furniture or
walls, between the device and the remote control. Ensure
visual contact between device and remote control.
Check the charging status of the batteries and change
them if required.
If the batteries have only just been changed, check them
for correct polarity and change them if required.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
EN 14
air cooler PAE 26
Maintenance
Maintenance intervals
Maintenance and care interval before every
start-up
as needed at least every
2 weeks
at least every
4 weeks
at least every
6 months
at least
annually
Clean the water tank
X X
Check the air inlets and outlets for
dirt and foreign objects and clean if
necessary
X X
Clean the exterior
X X
Visually check the inside of the
device for dirt
X X
Check the air filter for dirt and
foreign objects and clean if
necessary
X X
Replace the honeycomb filter
X
Check for damage
X
Check the attachment screws
X X
Test run
X
Maintenance and care log
Device type: .............................................
Device number: ....................................
Maintenance and care interval
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Clean the water tank
Check the air inlets and outlets for
dirt and foreign objects and clean if
necessary
Clean the exterior
Visually check the inside of the
device for dirt
Check the air filter for dirt and
foreign objects and clean if
necessary
Replace the honeycomb filter
Check for damage
Check the attachment screws
Test run
Remarks:
1. Date: ................................
Signature: ............................
2. Date: ................................
Signature: ............................
3. Date: ................................
Signature: ............................
4. Date: ................................
Signature: ............................
5. Date: ................................
Signature: ............................
6. Date: ................................
Signature: ............................
7. Date: ................................
Signature: ............................
8. Date: ................................
Signature: ............................
9. Date: ................................
Signature: ............................
10. Date: ..............................
Signature: ............................
11. Date: ..............................
Signature: ............................
12. Date: ..............................
Signature: ............................
13. Date: ..............................
Signature: ............................
14. Date: ..............................
Signature: ............................
15. Date: ..............................
Signature: ............................
16. Date: ..............................
Signature: ............................
15 EN
air cooler PAE 26
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Switch the device off.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Warning of electrical voltage
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
Visual inspection of the inside of the device for dirt
1. Remove the air filter.
2. Use a torch to illuminate the openings of the device.
3. Check the inside of the device for dirt.
4. If you see a thick layer of dust, have the inside of the
device cleaned by a specialist electrical company or by
Trotec.
5. Put the air filter back in.
Cleaning the housing
Clean the device with a soft, damp and lint-free cloth. Ensure
that no moisture enters the housing. Protect electrical
components from moisture. Do not use any aggressive cleaning
agents such as cleaning sprays, solvents, alcohol-based or
abrasive cleaners to dampen the cloth.
Cleaning the water tank
The water tank should be cleaned every two weeks.
Before a longer period of non-use or storage the water tank
should be drained.
1. Remove the water tank from the device.
2. Thoroughly rinse the water tank in a sink or similar.
3. Clean the tank using a mild cleaning agent (no detergent!).
4. Remove all calcium deposits in the water tank.
5. Dry the inside of the tank with a lint-free cloth.
6. Fill the water tank with fresh drinking water if you want to
continue operation (see chapter Adding water).
7. Refit the water tank into the device.
8. In doing so, make sure that the water tank is inserted
correctly, for otherwise the device cannot be switched
back on.
EN 16
air cooler PAE 26
Cleaning the air filter
The air filter has to be cleaned as soon as it is dirty. This is
brought to light e.g. by a reduced capacity (see chapter Errors
and faults).
Warning
Ensure that the air filter is not worn or damaged. The
corners and edges of the air filter must not be
deformed or rounded. Before reinserting the air filter,
make sure that it is undamaged and dry!
1. Remove the air filter from the device.
2. Remove the honeycomb filter from the air filter.
3. Clean the filter using a slightly damp, soft, lint-free cloth. If
the filter is heavily contaminated, clean it with warm water
mixed with a neutral cleaning agent.
4. Allow the filter to dry completely. Do not insert a wet filter
into the device!
5. Reinsert the honeycomb filter to the air filter.
6. Reinsert the air filter into the device.
Replacing the honeycomb filter
Note
When set to air cooling mode, the device should not be
operated without the honeycomb filter, otherwise
cooling will not work.
Note
Do not operate the device without an inserted air filter!
Without the air filter, the inside of the device will be
heavily contaminated. This could reduce the
performance and result in damage to the device.
The honeycomb filter should be replaced in case of heavy
soiling.
In standard operation, the interval for replacing the honeycomb
filter is approx. 1 year.
Allow the honeycomb filter to dry before removing it from the
device.
17 EN
air cooler PAE 26
1. Remove the air filter and the honeycomb filter from the
device.
2. Remove the honeycomb filter from the air filter.
3. Dispose of the used honeycomb filter according to the
national regulations.
4. Reinsert the honeycomb filter to the air filter.
5. Reinsert the air filter into the device.
Activities required after maintenance
If you want to continue using the device:
Reconnect the device to the mains.
If you do not intend to use the device for a considerable time:
Store the device according to the Storage chapter.
EN 18
air cooler PAE 26
Technical annex
Technical data
Parameter Value
Model PAE 26
Evaporation capacity 750 ml/h
Air flow rate 300 m
3
/h
Mains supply 220-240V/ 50Hz
Nominal current consumption 0.2 A
Power consumption 55 W
Sound pressure level
(1m distance)
65 dB(A)
Water tank capacity 4 l
Weight 7 kg
Dimensions
(length x width x height)
270 x 250 x 720 mm
Minimum distance to walls and
other objects:
top (A):
rear (B):
sides (C):
front (D):
20 cm
20 cm
20 cm
20 cm
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.
Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
info@trotec.com
www.trotec.com
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PAE26 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PAE26 in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PAE26

Trotec PAE26 User Manual - German - 21 pages

Trotec PAE26 User Manual - Dutch - 22 pages

Trotec PAE26 User Manual - French - 22 pages

Trotec PAE26 User Manual - Italian - 22 pages

Trotec PAE26 User Manual - Polish - 22 pages

Trotec PAE26 User Manual - Turkish - 22 pages

Trotec PAE26 User Manual - Spanish - 22 pages

Trotec PAE26 User Manual - Finnish - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info