727661
12
Zoom out
Zoom in
Previous page
1/23
Next page
12 EN
local air conditioner PAC 2010 SH / PAC 2610 S
Automatic switch-off
ü The device is switched on.
1. Press the Timer button(15).
ð The timer LED(12) is illuminated.
ð The number of hours flashes on the segment
display(13) for approx. 10s.
2. Repeatedly press the Up(19) or Down(18) button to select
the desired number of hours until automatic switch-off.
3. Press the Timer button(15) to confirm the setting.
ð The segment display(13) continuously indicates the
number of hours until automatic switch-off.
ð After the predefined time, the device switches itself off.
4. In order to delete the setting, press the Timer button(15)
again.
ð The timer LED(12) goes out.
Notes regarding automatic switch-off:
Pressing the On/ Off button(20) deactivates the automatic
switch-off function.
Automatic defrost
At low ambient temperatures, ice may form at the evaporator.
The device will then carry out an automatic defrost.
The compressor switches off and the fan keeps running until
defrosting is completed. The duration of the defrost process can
vary.
Do not switch the device off during automatic defrost. Do not
remove the mains plug from the mains socket.
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Switch off the device.
Hold onto the mains plug while pulling the power cable out
of the mains socket.
Empty the condensation tray if necessary.
If necessary, remove the condensation drain hose and any
residual fluid from it.
Clean the device according to the Maintenance chapter.
Store the device according to the Storage chapter.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damages.
Check the on-site fusing.
Observe the operating temperature according to the
Technical data chapter.
The condensation tray may be full. Empty the condensation
tray if necessary. The error codeE2 must not be indicated
on the segment display and the water filling level LED(10)
must not be illuminated.
Wait for 10minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device works with reduced or no cooling capacity:
Check whether cooling mode is selected.
Check the proper fit of the exhaust air hose. In case of
kinks, bends or blockage in the hose, exhaust air cannot
be discharged. Clear the way for the exhaust air.
Check the position of the ventilation flaps. They should be
opened to the maximum.
Check the air filter(s) for dirt. If necessary, clean or replace
the air filter(s).
Check the minimum distance to walls or other objects.
Position the device a little more in the room's centre if
required.
Check whether any windows and/or doors of the room are
open. If so, close them. One window has to remain open
for the exhaust air hose nonetheless.
Check the temperature setting at the device. Reduce the
set temperature if it is higher than the room temperature.
The device is loud or vibrates:
Check whether the device is set up in a stable and upright
position.
Condensate is leaking:
Check the device for leaks.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PAC2610S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PAC2610S in the language / languages: English as an attachment in your email.

The manual is 2,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PAC2610S

Trotec PAC2610S User Manual - German - 23 pages

Trotec PAC2610S User Manual - Dutch - 23 pages

Trotec PAC2610S User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info