756386
8
Zoom out
Zoom in
Previous page
1/11
Next page
8 EN
laser distance measuring device BD16
2. Briefly press the Switch-on/measurement button(7) to
carry out the first measurement (e.g.length).
3. Briefly press the Switch-on/measurement button(7) again
to carry out the second measurement (e.g.width).
ðUpon pressing the Switch-on/measurement button(7)
for the second time the device calculates the area and
displays this value in the lower measurement value
display. The most recently measured value will be
indicated in one of the upper measurement value
displays.
Performing a volume measurement
1. Briefly press the Function button(8) twice.
ðThe symbol
for volume measurement appears on
the display.
ðThe side to be measured in each case is indicated on
the display by flashing.
2. Briefly press the Switch-on/measurement button(7) to
carry out the first measurement (e.g.length).
3. Briefly press the Switch-on/measurement button(7) again
to carry out the second measurement (e.g.width).
4. Briefly press the Switch-on/measurement button(7) again
to carry out the third measurement (e.g.height).
ðUpon pressing the Switch-on/measurement button(7) for
the third time the device independently calculates the
volume and displays this value in the lower measurement
value display.
Performing a non-stop/ min and max measurement
Use the non-stop measuring function to correlate
measurements e.g. with construction drawings. With this
measurement method the device can be moved closer toward
the target with the measured value being recalculated roughly
every 0.5seconds. The corresponding maximum and minimum
measured values are displayed in the first and second line
respectively.
For instance, you can direct the laser beam at a wall and then
retreat from it step by step. Keep reading the measured values
until the desired distance is achieved.
1. Press the Switch-on/measurement button(7) for a long
time until the max(21), min(19) and Δ indications(17)
appear on the display.
2. With reference to the target point, move the device slowly
back and forth as well as up and down (e.g.in a corner).
3. Briefly press the Switch-on/measurement button(7) to
terminate the non-stop measurement.
ðThe maximum and minimum measured values and the
difference(Δ) between these two are indicated on the
display. Additionally, the last measured value will be
displayed in the bottommost line.
Indirect height measurement (Pythagoras)
Using this method the length of an unknown straight-line
segment can be determined via the Pythagorean Theorem. This
method is suitable for e.g. height measurements.
A
B
Measurement requirements:
The device is aligned horizontally to the lowest point (B) of
the line segment to be determined.
The reference point is located at the rear of the device. See
chapter Setting the reference value.
1. Briefly press the Function button(8) three times.
ðThe symbol for indirect measurements appears on
the display.
ðThe bar with number 1 (hypotenuse) flashes.
2. Aim the device at the highest point(A) and briefly press the
Switch-on/measurement button(7) once to perform a
measurement. Make sure to hold the device as steady as
possible and place it level on the ground with the two rear
edges. The position at the two rear edges must not be
changed during the measurements!
ðDie Länge der Strecke wird in der oberen
Messwertanzeige in der 1. Zeile angezeigt.
3. Align the device horizontally (point B) and briefly press the
Switch-on/measurement button(7) one time to measure
the horizontal distance.
ðThe second measured value will be indicated in the
second line of the upper measurement value display.
ðThe line segment to be determined is displayed as
result in the lower measurement value display(15).
Twofold indirect height measurement
This method is suitable for e.g. height measurements.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec BD16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec BD16 in the language / languages: English as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec BD16

Trotec BD16 User Manual - German - 11 pages

Trotec BD16 User Manual - Dutch - 12 pages

Trotec BD16 User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info