464874
9
Zoom out
Zoom in
Previous page
1/13
Next page
10 GB/IE/CY
Operation
Q
Reset / deleting settings
After connection to the power supply, the appliance
automatically returns to its basic setting and remains
in STANDBY mode
Q
Switching between modes 1,
2, 3 and 4
j Press the MODE selection button
9
the appro-
priate number of times.
The device switches between charging modes in
the following order: Standby
, MODE 1
„6 V“, MODE 2
, MODE 3 , MODE 4
and then repeats the cycle
NOTE: If you press the selector button
9
, charging
mode automatically switches over to the next mode
and begins operation in that mode.
NOTE: However, if a battery is not disconnected
from the charging station after a full charge, the
appliance remains in trickle-charge mode, even if
the user switches over to another mode. This pro-
tects the battery from being damaged.
Q
Mode 1 „6 V“ (7.3 V / 0.8 A)
This mode is suitable for charging 6 V lead-acid
batteries with a capacity less than 14 Ah.
j Press the selection button MODE
9
, to select
mode 1. After doing so, the corresponding LED
display „6 V“
2
lights up. If you do not activate
an-other process afterwards, the electronic sys-
tem will automatically start the charging process
together with the LED display
8
at (with a
current of) 0.8 A ± 10 %. If the procedure runs
without any problems, the LED display
8
remains on during the entire charging proc
ess,
un-
til the battery is fully charged at 7.3 V / ±
0.25 V.
When the battery is fully charged, LED display
7
lights up and LED display
8
goes
out. The device now switches automatically into
maintenance charging mode.
Q
Mode 2 12 V“ (14.4 V / 0.8 A)
This mode is suitable for charging 12 V lead-acid
batteries with a capacity less than 14 Ah.
j Press the selection button MODE
9
, to activate
mode 2. After completion of this process, the
appropriate LED indicator
3
lights up.
Then if you do not take any further action, the
electronic control and the LED indicator
8
automatically switches on and starts the charg-
ing process. If the procedure runs without any
problems, the LED display
8
remains on
during the entire charging process, until the
battery is fully charged. When the battery is
fully charged, LED display
7
lights up and
LED display
8
goes out. The device now
switches automatically into maintenance charg-
ing mode.
Q
Mode 3 „12 V“ (14.4 V / 3.6 A)
This mode is mainly suitable for charging 12 V
lead-acid batteries with a capacity greater than
14 Ah under normal conditions.
j Press the selection button MODE
9
, to activate
mode 3. Then if you do not take any further ac-
tion, the electronic control and the LED indicator
4
switches on and starts the charging
process. If the process runs without any problems,
the LED indicator
8
remains on during the
whole charging process until the battery is
charged. When the battery is fully charged, the
LED indicator
7
and the die LED indicator
8
go out. The device now switches auto-
matically into maintenance charging mode.
Q
Mode 4 “12 V” (14.7 V / 3.8 A)
This mode is used for charging 12 V lead-acid bat-
teries with a capacity greater than 14 Ah under
cold conditions or for charging some AGM (Absorb-
ent Glass Mat) batteries with a capacity greater
than 14 Ah.
33211_Battery charger_Content_LB6.indd 10 24.06.09 10:30
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tronic KH 3033 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tronic KH 3033 in the language / languages: English as an attachment in your email.

The manual is 2,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Tronic KH 3033

Tronic KH 3033 User Manual - German, Dutch, French - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info