737169

Tronic KH 3002 IAN 33212 Manual

46
Zoom out
Zoom in
Previous page
1/62
Next page
- 44 -
Possible faults in the event of
non-functionality
• If neither of the two LEDs, 5 and 6, light up after
switching on, then the 10 amp fuse 7 on the
Energy Station might have blown. Changing fuses
is described in more detail in the section "Fuses".
• Should an LED light up on the Energy Station after
switching on, but the appliance fails to work, im-
mediately switch the Energy Station off. Check to
ensure that the cable is correctly connected –
and that “Positive” and “Negative“ have not
been switched. If required, also check the fuse in
your appliance, as described in its operating
instructions.
Power supply over the screw
connections
Caution!
Before performing any connections, always check
to ensure that both the appliance to be supplied
and the Energy Station are switched off. Place the
main switch 2 in the “OFF” position (centre position).
In this way you can avoid damage through connec-
tion faults.
Use the screw connections 9 at the rear of the ap-
pliance for 12V appliances requiring a high starting
current for switching on, but which do not otherwise
consume more than 10 A per hour.
Appliances with a high starting current could be for
instance ...
- 12 V vacuum cleaners
- 12 V drilling machines
- 12 V television sets etc.
Although these may not require more than 10 A
in operation, the fuse will immediately blow when
they are switched on. In this case such appliances
cannot be operated on the 12 V/10 A socket 3.
Operate these appliance only by way of the screw
connections 9, as described here.
Carrying out connections using the
banana plugs
1. The screw connections 9 are hollow, to accom-
modate so-called “banana plugs”. If such are
provided on your appliance cable, you can insert
these in the screw connections 9 from the top,
instead of screw-connecting.
Danger!
Extremely high current flows are possible here, ones
that are even capable of heating thick cables to red
hot! Before connecting, check to ensure that the
connecting cable for the appliance to be powered
is suitable for such a connection, so as to avoid
electric shock and the risk of fire.
These high currents are required for the starting of
some appliances. The screw connections 9 are
therefore neither routed by way of a fuse and nor
by way of the main switch 2, i.e. voltage is
continuously present!
For this reason it is imperative to ensure that a short-
circuit cannot be created at the screw terminals,
not under any circumstances!
Carrying out connections with the
bare ends of fixed appliance cables
1. If the cable is permanently connected with the
appliance to be powered, you can simply con-
nect the bare “Positive“ wire (usually red) to the
red screw connector 9.
2. Connect the bare "Negative" wire (usually black
or blue) to the black screw terminal 9.
To do so, unscrew the plastic caps on the screw
terminals 9. Clamp the bare wires underneath
when retightening.
Carrying out connections over a loose
cable
1. If the cable is not permanently connected to the
appliance being powered, but has a bare ap-pli-
ance plug available, first insert the appliance
plug in the socket on the appliance.
… 46 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tronic KH 3002 IAN 33212 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tronic KH 3002 IAN 33212 in the language / languages: Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Tronic KH 3002 IAN 33212

Tronic KH 3002 IAN 33212 User Manual - English - 14 pages

Tronic KH 3002 IAN 33212 User Manual - German, Dutch, French - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info