Manual Triton TWSS10 (page 5 of 134) (English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish)

665091

Zoom out

Zoom in

1/134

General Power Tool Safety Warnings

WARNING! When using electric power tools, basic safety precautions should always be

followed to reduce the risk of ﬁre, electric shock and personal injury including the following

safety information. Read all these instructions before attempting to operate this product and

save these instructions for future use.

WARNING: This appliance is not intended for use by persons (including children) with reduced,

physical or mental capabilities or lack of experience or knowledge unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their

safety. Children must be supervised to ensure that they do not play with the appliance.

CAUTION: Use the power tool, accessories and tool bits etc. in accordance with these

instructions, taking into account the working conditions and the work to be performed. Use

of the power tool for operations different from those intended could result in a hazardous

situation.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1 - Keep work area clear - Cluttered areas and benches invite injuries

2 - Consider work area environment

- Do not expose tools to rain

- Do not use tools in damp or wet locations

- Keep work area well lit

- Do not use tools in the presence of ﬂammable liquids or gases

3 - Guard against electric shock - Avoid body contact with earthed or grounded surfaces

(e.g. pipes, radiators, ranges, refrigerators)

4 - Keep other persons away - Do not let persons, especially children, not involved in the

work touch the tool or the extension cord and keep them away from the work area

5 - Store idle tools - When not in use, tools should be stored in a dry locked-up place, out

of reach of children

6 - Do not force the tool - It will perform the job better and safer at the rate for which it

was intended

7 - Use the right tool - Do not force small tools to do the job of a heavy duty tool

- Do not use tools for purposes not intended; for example do not use circular saws to cut

tree limbs or logs

8 - Dress appropriately

- Do not wear loose clothing or jewellery, which can be caught in moving parts

- Suitable safety footwear is recommended when working outdoors.

- Wear protective covering to contain long hair

9 - Use protective equipment

- Use safety glasses

- Use face or dust mask if working operations create dust

WARNING: Not using protective equipment or appropriate clothing can cause personal injury or

increase the severity of an injury.

10 - Connect dust extraction equipment - If the tool is provided for the connection of dust

extraction and collecting equipment, ensure these are connected and properly used

11 - Do not abuse the power cable - Never yank the power cable to disconnect it from the

socket. Keep the power cable away from heat, oil and sharp edges. Damaged or entangled

power cables increase the risk of electric shock

12 - Secure work - Where possible use clamps or a vice to hold the work. It is safer than

using your hand

13 - Do not overreach - Keep proper footing and balance at all times

14 - Maintain tools with care

- Keep cutting tools sharp and clean makes the tool easier to control and less likely to

bind or lock in the workpiece

- Follow instruction for lubricating and changing accessories

- Inspect tool power cables periodically and if damaged have them repaired by an

authorized service facility

- Inspect extension cables periodically and replace if damaged

- Keep handles dry, clean and free from oil and grease

WARNING: Many accidents are caused by poorly maintained power tools.

15 - Disconnect tools - When not in use, before servicing and when changing accessories

such as blades, bits and cutters, disconnect tools from the power supply

WARNING: The use of accessories or attachments not recommended by the manufacturer may

result in a risk of injury to persons.

16 - Remove adjusting keys and wrenches - Form the habit of checking to see that keys

and adjusting wrenches are removed from the tool before switching it on

17 - Avoid unintentional starting - Ensure switch is in “off’ position when connecting to a

mains socket or inserting a battery pack, or when picking up or carrying the tool

WARNING: Unintended starting of a tool can cause major injuries.

18 - Use outdoor extension leads - When the tool is used outdoors, use only extension

cords intended for outdoor use and so marked. Use of an extension cable suitable for

outdoor use reduces the risk of electric shock

19 - Stay alert

- Watch what you are doing, use common sense and do not operate the tool when you are

tired

- Do not use a power tool while you are under the inﬂuence of drugs, alcohol or

medication

WARNING: A moment of inattention while operating power tools may result in serious personal

injury.

20 - Check damaged parts

- Before further use of tool, it should be carefully checked to determine that it will operate

properly and perform its intended function

- Check for alignment of moving parts, binding of moving parts, breakage of parts,

mounting and any other conditions that may affect its operation

- A guard or other part that is damaged should be properly repaired or replaced by an

authorized service centre unless otherwise indicated in this instruction manual

- Have defective switches replaced by an authorized service centre

WARNING: Do not use the tool if the on/off switch does not turn it on and off. The switch must

be repaired before the tool is used.

21 - Have your tool repaired by a qualiﬁed person - This electric tool complies with the

relevant safety rules. Repairs should only be carried out by qualiﬁed persons, otherwise

this may result in considerable danger to the user

WARNING: When servicing use only identical replacement parts.

WARNING: If the power cable is damaged it must be replaced by the manufacturer or an

authorised service centre.

22 - Power tool mains plugs must match the mains socket - Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodiﬁed plugs

and matching sockets will reduce risk of electric shock

23 - If operating a power tool outside use a residual current device (RCD) - Use of an

RCD reduces the risk of electric shock

NOTE: The term “residual current device (RCD)” may be replaced by the term “ground fault

circuit interrupter (GFCI)” or “earth leakage circuit breaker (ELCB)”.

WARNING: When used in Australia or New Zealand, it is recommended that this tool is ALWAYS

supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less.

WARNING: Before connecting a tool to a power source (mains switch power point receptacle,

outlet, etc.) be sure that the voltage supply is the same as that speciﬁed on the nameplate of

the tool. A power source with a voltage greater than that speciﬁed for the tool can result in

serious injury to the user, and damage to the tool. If in doubt, do not plug in the tool. Using a

power source with a voltage less than the nameplate rating is harmful to the motor.

Polarized Plugs (for North America only) To reduce the risk of electric shock, this equipment

has a polarized plug (one blade is wider than the other). This plug will ﬁt in a polarized outlet

only one way. If the plug does not ﬁt fully in the outlet, reverse the plug. If it still does not

ﬁt, contact a qualiﬁed electrician to install the proper outlet. Do not change the plug in any way.

Wetstone Sharpener Safety

WARNING!

• Hold the power tool by insulated gripping surfaces only, because the grinding wheel

may contact its own cord. Cutting a “live” wire may make exposed metal parts of the

power tool “live” and could give the operator an electric shock.

• The machine is Class 1 Category (earthed) and is ﬁtted with a 3-core cable and

plug. Should the cable or plug be damaged, the product should be serviced by an

authorized Service Centre to avoid a hazard.

• It is strongly recommended that the tool always be supplied via a residual current

device with a rated residual current of 30 mA or less.

a) Wear adequate personal protective equipment including suitable safety glasses and

breathing protection. DO NOT wear loose clothing, REMOVE jewellery and tie long hair

back. DO NOT eat, drink or smoke in the work area. Keep children away

b) ALWAYS stand securely when working with this machine. NEVER lean over the

rotating wheels or overreach. ALWAYS be prepared to counteract kickback. Depending on

the orientation and rotation of the grinding wheel, a workpiece might be pulled out of your

hands or be thrown towards you

c) This machine is designed for the sharpening of tools and common household

blades. It is not intended for other grinding purposes, nor should it be used to grind other

materials not commonly used for tool blades

d) Sharpening should only be undertaken by persons familiar with the procedures,

necessary techniques and hazards involved. This manual only outlines the general use

of the machine, and cannot replace formal training in metalwork and tool sharpening or

practice

e) If you are unsure how to use the machine to sharpen tools safely and according to

rules and regulations, DO NOT use

f) ALWAYS adhere to the tool manufacturer’s guidelines regarding sharpening and

maintenance. If the guidelines are unclear, return the tool to the manufacturer for

sharpening

g) NEVER attempt to sharpen a blade that is not intended to be sharpened. Some

blades (e.g. some power tool blades) must be replaced when blunt, worn or

damaged and CANNOT be sharpened and re-used

949257_Z1MANPRO2.indd 5 16/03/2016 16:53

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Triton TWSS10 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 19,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Triton TWSS10 Manual

Product: