5
GB
Sound and vibration levels in the specification are determined according to EN60745 or
similar international standards.
working conditions.
increased levels of noise and vibration. www provides information on sound
and vibration levels in the workplace that may be useful to domestic users who use tools for
long periods of time.
General P
WARNING!
followed to reduce the risk of fire, electric shock and personal injury including the following
safety information. Read all these instructions before attempting to operate this product and
save these instructions for future use.
WARNING:
physical or mental capabilities or lack of experience or knowledge unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety
CAUTION:
instructions, taking into account the working conditions and the work to be performed.
of the power tool for operations different from those intended could result in a hazardous
situation.
The term “power tool”
battery-operated (cordless) power tool.
1 - Keep work area clear - Cluttered areas and benches invite injuries
2 - Consider work area environment
- Do not expose tools to rain
- Do not use tools in damp or wet locations
- Keep work area well lit
- Do not use tools in the presence of flammable liquids or gases
3 - Guard against electric shock - Avoid body contact with earthed or grounded surfaces
(e.g. pipes,
4 - Keep other persons away - Do not let persons, especially children,
work touch the tool or the extension cord and keep them away from the work area
5 - Store idle tools - When not in use,
of reach of children
6 - Do not force the tool - It will perform the job better and safer at the rate for which it
was intended
7 - Use the right tool - Do not force small tools to do the job of a heavy duty tool
- Do not use tools for purposes not intended; for example do not use circular saws to cut
tree limbs or logs
8 - Dress appropriately
- Do not wear loose clothing or jewellery
- Suitable safety footwear is recommended when working outdoors.
- W
9 - Use protective equipment
- Use safety glasses
- Use face or dust mask if working operations create dust
WARNING:
increase the severity of an injury.
10 - Connect dust extraction equipment - If the tool is provided for the connection of dust
extraction and collecting equipment, ensure these are connected and properly used
11 - Do not abuse the power cable - Never yank the power cable to disconnect it from the
socket.
entangled power cables increase the risk of electric shock
12 - Secure work - Where possible use clamps or a vice to hold the work.
using your hand
13 - Do not overreach - Keep proper footing and balance at all times
14 - Maintain tools with care
- Keep cutting tools sharp and clean makes the tool easier to control and less likely to
bind or lock in the workpiece
- Follow instruction for lubricating and changing accessories
- Inspect tool power cables periodically and if damaged have them repaired by an
authorized service facility
- Inspect extension cables periodically and replace if damaged
- Keep handles dry,
WARNING:
15 - Disconnect tools - When not in use,
such as blades, bits and cutters,
WARNING:
result in a risk of injury to persons.
16 - Remove adjusting keys and wrenches - Form the habit of checking to see that keys
and adjusting wrenches are removed from the tool before switching it on
17 - Avoid unintentional starting - Ensure switch is in “off’ position when connecting to a
mains socket or inserting a battery pack, or when picking up or carrying the tool
WARNING:
18 - Use outdoor extension leads - When the tool is used outdoors,
cords intended for outdoor use and so marked. Use of an extension cable suitable for
outdoor use reduces the risk of electric shock
19 - Stay alert
- W
tired
- Do not use a power tool while you are under the influence of drugs, alcohol or
medication
WARNING:
injury.
20 - Check damaged parts
- Before further use of tool, it should be carefully checked to determine that it will operate
properly and perform its intended function
- Check for alignment of moving parts, binding of moving parts,
mounting and any other conditions that may affect its operation
- A guard or other part that is damaged should be properly repaired or replaced by an
authorized service centre unless otherwise indicated in this instruction manual
- Have defective switches replaced by an authorized service centre
WARNING:
be repaired before the tool is used.
21 - Have your tool repaired by a qualified person - This electric tool complies with the
relevant safety rules. Repairs should only be carried out by qualified persons,
this may result in considerable danger to the user
WARNING:
WARNING:
authorised service centre.
22 - Power tool mains plugs must match the mains socket - Never modify the plug in any
way
plugs and matching sockets will reduce risk of electric shock
23 - If operating a power tool outside use a residual current device (RCD) - Use of an
RCD reduces the risk of electric shock
NOTE:
circuit interrupter (GFCI)” or
WARNING:
outlet, etc.) be sure that the voltage supply is the same as that specified on the nameplate of
the tool.
serious injury to the user
power source with a voltage less than the nameplate rating is harmful to the motor.
Polarized Plugs (for North
has a polarized plug (one blade is wider than the other).
only one way
fit, contact a qualified electrician to install the proper outlet.
Oscillating Spindle Sander Safety
WARNING!
• Hold the power tool by insulated handles or gripping surfaces only
sanding belt/sheet may contact its own cord. Cutting a “live”
metal parts of the power tool ‘live’ and could give the operator an electric shock.
• Recommendation that the tool always be supplied via a residual current device with
a rated residual current of 30 mA or less.
• If the replacement of the supply cord is necessary,
manufacturer or his agent in order to avoid a safety hazard.
The warnings, precautions,
possible conditions and situations that may occur The operator must understand that
common sense and caution are factors which cannot be built into this product, but must be
supplied by the operator
Do not operate the spindle sander until it is fully assembled and you have read and understood
the following instructions and the warning labels on the spindle sander
a) Check the condition of the spindle sander If an
operate properly,
b) Determine the type of work you are going to be doing before operating the spindle
sander
c) Secure your work. Support the workpiece securely on the table, and hold it with both
hands.
d) Be aware of the direction of feed. Feed the workpiece into the sanding sleeve against
the direction of rotation of the sanding sleeve.
e) Always keep your hands out of the path of the sander and away from the sanding
sleeves. Avoid hand positions where a sudden slip could cause your hand to move into the
spindle. Do not reach underneath the workpiece or around the sanding sleeve while the
spindle is rotating.
f) Disconnect the sander after turning off the power switch. W
rotating before performing maintenance.
use or when changing insert plates, sanding sleeves,
516693_Z1MANPRO1.indd 5 30/08/2016 16:28
