Manual Triton T41200BS (page 9 of 84) (English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish)

665070

Zoom out

Zoom in

1/84

6. Check that the sanding belt is securely ﬁxed to the sander and that it is correctly aligned

while the tool is operating. If necessary, switch the sander OFF and re-ﬁx to the sander

WARNING: DO NOT use the sander inverted unless it is securely clamped to the work surface.

Note: When the belt sander is being clamped, use the Bench-Mounting Mat (17) beneath the

belt sander to protect the work surface from damage and to prevent the belt sander from

moving.

Accessories

• A full range of different grit sanding belts and accessories is available from your Triton

stockist. Spare parts can be obtained from toolsparesonline.com

Maintenance

WARNING: Always disconnect from the power supply before carrying out any inspection,

maintenance or cleaning.

Emptying the dust collection bag (if ﬁtted)

WARNING: Always switch the belt sander OFF and disconnect from the power supply before

detaching the Dust Collection Bag (20) or dust extraction system.

1. To remove the Dust Collection Bag, rotate outwards to disengage the bayonet, then pull off

(Image A)

2. Unzip the Dust Collection Bag, empty, and reﬁt (see ‘Connecting the Dust Collection Bag’)

Note: If the sanding dust contains harmful substances, such as particles from old paint,

varnish, surface coatings etc, always dispose of in accordance with laws and regulations.

Note: For optimum dust removal, empty the Dust Collection Bag when it is no more than

half full.

Note: Always clean the tool THOROUGHLY when switching from sanding wood to sanding metal

and vice versa.

General inspection

• Regularly check that all the ﬁxing screws are tight. They may vibrate loose over time

• Inspect the mains cord of the tool, prior to each use, for damage or wear. Repairs should

be carried out by an authorised Triton service centre. This advice also applies to extension

cords used with this tool; always check for wear or damage and see the manufacturer of

the product for repairs, if possible

Cleaning

• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly and

shorten the machine’s service life. Clean the body of your machine with a soft brush, or

dry cloth. If available, use clean, dry, compressed air to blow through the ventilation holes

• Clean the tool casing with a soft damp cloth using a mild detergent. Do not use alcohol,

petrol or strong cleaning agents

• Never use caustic agents to clean plastic parts

Lubrication

• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant

Brushes

• Over time the carbon brushes inside the motor may become worn

• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking

• If you suspect that the brushes may be worn, both brushes will need replacing

simultaneously

Replacing the brushes:

WARNING: Ensure that the belt sander is switched OFF and the mains power cord is

unplugged from the power source before attempting to replace the brushes.

1. Locate the Vented Motor Cover (12) on the belt sander and the two screw-in Brush Covers

(13)

2. Remove the Brush Covers with a ﬂat-tipped screwdriver, then remove the two brushes

3. Note the notches on the brush ends, which align with the ﬁtment in the Brush Cover holes,

and place the new brush inside then screw the Brush Cover back in

Note: Fitting the new brushes can be done one at a time, but it is recommended that both

brushes be replaced during the same session.

4. Once both brushes have been replaced, plug the belt sander in to the power socket and

switch ON. Run the belt sander to test that the replacement has worked

5. If there is no power, retry from step 1. If there is still no power after a second attempt to ﬁt

the brushes, see your Triton service technician

Changing the drive belt

Note: A spare drive belt is supplied with the sander. Further replacements and other spare

parts are available from your Triton stockist or from toolsparesonline.com.

1. Using a Phillips screwdriver, remove the screws holding the Drive Belt Cover (5) in place

2. Remove the worn belt by easing it off the bottom, larger drive pulley, and then lift away

3. Clean all dust and debris away, if any

4. Place the new drive belt over the top drive pulley and push onto the larger puller, then rotate

the belt until it is on both pulleys and located in the grooves of each pulley

5. Replace the Drive Belt Cover and screw the ﬁxing screws tight

6. Test the belt sander on a low speed. If ﬁtted correctly, the belt sander is ready to use

Storage

• Store this tool carefully in a secure, dry place out of the reach of children

Disposal

Always adhere to national regulations when disposing of power tools that are no longer

functional and are not viable for repair.

• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE),

with household waste

• Contact your local waste disposal authority for information on the correct way to dispose

of power tools

490239_Z1MANPRO2.indd 9 04/07/2016 17:01

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Triton T41200BS in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 6,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Triton T41200BS Manual

Product: