530942

Tristar WR-1995 Manual

39
Zoom out
Zoom in
Previous page
1/79
Next page
PUTTING INTO SERVICE-TEMPERATURE SETTINGS
Digital Tube1: Indicate the current temperature or preset temperature of upper layer. When +/- Key is
pressed, display on the digital tube flashes, indicating the preset temperature .If no temperature setting
operation occurs within five seconds, the system will automatically return to the display of ambient
temperature in the storage cabinet, with the accuracy of 1℃(1℉)
The introduction about malfunction code: E2 Faults of upper layer’s cabinet temperature sensor.
The sensor is short circuit or open circuit.(10seconds later the system will close and this code will
display. The buzzer will tweet every 2 seconds.)
E9 is Superheating protection. After compressor operating 4 hours under any condition, when the upper
layer sensor detects the cabinet temperature no less than 25℃ (77℉),the buzzer will alarm and tweet
every 2 seconds. When the detected cabinet temperature is ＞30℃,“E9”malfunction code will display.
The Electrical Heating will close and compressor will go on working.(The buzzer will tweet every 2
seconds). When Upper layer sensor detects the cabinet Temperature reaches 21℃, the system will
restart automatically and the temperature will display normally.
Preset Temperature Adjusting Key for Upper Layer: Press this key to adjust the preset temperature
of upper layer. Every time it is pressed, the preset temperature of upper layer is increased or decreased
by 1℃(1℉).Temperature setting range is 12℃-22℃(54℉-72℉)
Digital Tube2: Indicate the current temperature or preset temperature of lower layer. When +/- Key is
pressed, display on the digital tube flashes, indicating the preset temperature .If no temperature setting
operation occurs within five seconds, the system will automatically return to the display of ambient
temperature in the storage cabinet, with accuracy of 1℃(1℉)
The introduction about malfunction code: E3 faults of lower layer’s cabinet temperature sensor. The
sensor is short circuit or open circuit.(10 seconds later the system will close and this code will display.
the buzzer will tweet every 2 seconds)
E8 is Supercooling protection. When the lower layer sensor detects the cabinet temperature reaches 3
℃(37℉), the compressor will stop, but electrical heating keeps going on.”E8”
Malfunction code will display.(The buzzer will tweet every 1 second). When the detected cabinet
temperature is no less than 6℃(43℉),the system will restart automatically and the temperature will
display normally.
Preset Temperature Adjusting Key for Lower Layer: Press this key to adjust the preset temperature
of lower layer. Every time it is pressed, the preset temperature of lower layer is increased or decreased
by 1℃(1℉). temperature setting range is 5℃-12℃(41℉-54℉)
Compressor Indicator LED: This LED comes on while the compressor is operating, and goes out
when the compressor stops operation.
Electric Heating Indicator LED: this LED comes on during operation of electric heating device and
goes out when electric heating device stops operation.
5
Electric Heating
Indication LED
Test key
Preset temperature adjusting
Key for Lower Layer
Digital Tube 2
Preset temperature
adjusting Key for upper
Layer
Compressor
Indication LED
ON/OFF Key
Digital Tube 1
4
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tristar WR-1995 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tristar WR-1995 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info