530991

Tristar SM-6001 Manual

11
Zoom out
Zoom in
Previous page
1/87
Next page
21
Inserting the needle
Attention: Turn power to “off” position before inserting the needle, to avoid electrical shock.!~!
Change the needle regularly, especialy if it is showing signs of wear and causing problems.
Insert the needle as follows:
Loose the needle clamp screw(no.13) and tighten again after
inserting the new needle.
The flat side of the needle should be towards the back. Insert
the needle as far up as it will go.
(Needle clamp screw no.13)
Attaching the presser foot holder
The machine has the standard pressure foot, used for sewing of different fabrics. For the
sewing of button holes and zippers you have to place another pressure foot on the machine.
See the following description with illustrations how to replace the pressure foot.
Figure 1. Put the pressure foot lever (no.18) up. Place the foot clamp (B) on the pressure foot
lever and tighten screw A fixed.
Figure 2. Lower the foot lever until the notch (C) is right above the pin (D) of the pressure foot
area. Press E and lift the pressure foot so that pin D is exactly C recess, then loose
lever E.
Figure 3. Removing the pressure foot.
Lift the pressure foot lever, press lever E and the pressure foot falls off.
Presser
foot lever
No.18
E
A E C
Presser
B D foot
22
Threading the upper thread.
For quick and easy installation of the upper thread follow the numbers 1 to 8 by the black
dotted line in the diagram below. The enlargements can be a clarification of the step.
1. Put the bobbin on the bobbin winder (no.5) and guide the thread through
the winding
thread guide (no.7) from the back to the front.
2. Push thread tension release bar to left, then guide the thread down between the
tension disc making sure that the thread has been inserted into the tension disc.
3. Continue to draw the thread down and around the thread pulling bar fixed holder
spring from left to right.
4. Draw the thread up, through the take-up lever draw from left to right.
5. Continue to draw the thread down through the thread take-up lever from front to
back.
6. Drawing down the thread and through the lower guide from back to front.
7. Continue to draw down the thread through the thread protector.
8. Finally thread the needle from front to back
(important !!!!)
Fixed thread holder
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tristar SM-6001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tristar SM-6001 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info