530952
3
Zoom out
Zoom in
Previous page
1/16
Next page
Part list
A
B
C
D
E
F
G
H
I
J
K
L
Stirring Vessel
Please insure that the drive shaft is installed properly at the bottom of the mixing cup (F).
The food volume should not exceed the maximum capacity of the mixing cup (F) (approximately
400ml).
The temperature for mixing the food should not higher than 80 degrees.
Do not put your fingers or any thing into the mixing cup (F) when it is connecting to the electricity
supply. Only when the electricity supply is cut off, than you can deal with the food attached to the
wall of the mixing cup.
Do not demolish the mixing cup (F) when it is still at work.
Equipped with safety locks
The product is equipped with a safety lock (L). When the mixing cup (F) is not or inappropriately
installed, the dynamo (B) can not work.
Usage Instructions
Please clean the parts which contact with the food before you use the product for the first time
(see chapter cleaning)
Put the food into the mixing cup (F) under the specified capacity (approximately 400ml).
Put the mixing cup into the safety lock (L), the cup should than rest on the cup holder (J)
Please insure that the plug (H) is connected and the mixing cup (F) is installed properly before
you start the product.
Press the speed control/ on/ off button (I) and start the dynamo (B). Press ‘I’ for fine mixing and
press ‘II’ for the more rough mixing, press ‘0’ for finish mixing.
During the mixing process (not longer than 2 minutes), do not put raw material into the mixing
cup; only after the electricity supply is cut off and the machine stops, can raw material be added
into the mixing cup.
Cleaning
Please use water to clean the parts which contact with the food after using it. Install the
stirring vessel properly(see usage Instruction), detergent warm water into the mixing cup.
Please cut off the power (speed control/ on/off button (I) at ‘0’) before cleaning it.
Generally, dish-washer can not be used to clean the product or the spare parts.
Soft wet cloth can be used to polish the dynamo (B), do not immerse dynamo (B) in water.
Do not use abrasive, brusher or alcohol, etc.
Demolish the mixing cup (F) and rinse it out with clean warm water.
A: Dynamo cover
B: Dynamo
C: Drive shaft
D: Stirrer
E:Stirring rod
F: Mixing cup
G: Base
H: Plug
I: Speed control/ on/off switch
J: Cup holder
K: Holder
L: Safety lock for the cup
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tristar BL-4425 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tristar BL-4425 in the language / languages: English, German, Dutch, French, Italian, Portuguese as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info