775413

Trek Sensor Manual

3
Zoom out
Zoom in
Previous page
1/4
Next page
Odometer (total distance)
(0.0-9999 kms or 6213 miles)-ODO
The total distance is continuously measured, accumulated and
displayed until next reset or the battery is changed. When 9999
kms or 6213 miles is reached the odometer returns to zero and
counting begins anew.
Trip Distance
(0.0-999.9 kms)-DIS
The trip distance from start to current point is displayed. Trip
distance will start calculating if signal is received, and stop
calculating when signal stops.
Auto Start/Stop
All functions - Current Speed(S), Odometer(ODO) and Trip Distance(DIS) will
automatically start and stop when signal is received or stopped.
Auto Scan
All the functions (ODO, DIS) will automatically scan and each display mode will
last 3 seconds. This function will continue until battery change/reset.
Auto Power Saving
When unit has not been used for 10 minutes (no signal received for ten
minutes continuously), the display will disappear and power will be
automatically saved. Start pedaling to release power saving mode and display
all functions automatically (auto scan).
Auto Clear data
When unit has not been used for 6 hours (not receiving and input signal for 6
hours continuously), all data stored in memory will be erased (wheel
circumference, odometer and speed scale will be kept). Once you start
pedaling (receiving signals), all data will calculate from zero.
5. Loosen the spoke screw and place spoke in spoke channel.
6. Tighten spoke screw so that it cinches the magnet securely
to the spoke.
7. Place the wheel sensor on the appropriate fork leg.
8. Install the zip tie through wheel sensor and pull tight.
9. Adjust the wheel sensor until it is 3-5mm from the wheel magnet. The
magnet should line up with indent on wheel sensor.
Test
Mount the computer in the bracket. Lift the front wheel off the ground and
spin the wheel checking if current speed is displayed. If not, adjust wheel
magnet and wheel sensor as described in installation steps 9. Refer to the
following steps for the operation of your Sensor computer.
Display Functions
Current Speed (0.0-70 miles or 99
kms)-S
The current speed is displayed on the upper line of the display and updated
every second.
Page 5Page 4
Spoke
Screw
Spoke
Channel
Speed 0-30km/h 31-60km/h over 60 m/h
Minimal display unit 0.1km/h(mile/h) 0.5km/h(mile/h) 1km/h(mile/h)
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trek Sensor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trek Sensor in the language / languages: English as an attachment in your email.

The manual is 0.09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info