648026
33
Zoom out
Zoom in
Previous page
1/148
Next page
34
ENGLISH
To enter programming mode, press buttons ‘On/Off’ and ‘Mode-switch’ for two seconds. Four
zeros will appear, with the first zero blinking.
Enter the appropriate code by pressing button ‘+’ for a higher value, ‘-’ for a lower value. Press
button ‘On/Off’ to select a value and move to the next digit. After entering the correct value for the
fourth digit, press button ‘On/Off’ to move into the chosen menu. In the programming menu,
buttons ‘+’ and ‘-’ will move to a higher or lower value. Pressing button ‘On/Off’ will save the entry
and move you to the next step, or back to the regular display.
Codes
2001 allows you to switch between miles and kilometers.
2004 allows you to set the time.
2009 allows you to swap the function of the buttons from left to right and vice versa.
3771 allows you to set the correct wheel diameter.
2011 allows you to change the display language. Use button to scroll through the languages.
5. Maintenance
After the first two to three weeks of use, or 300km, have your dealer check the spokes in the rear wheel.
Check the connections of the system every two to three months. Make sure that no dirt or moisture
can get into the ‘docking station’ (connector) when the battery-pack is not on the bike. If you notice
anything like this, clean with a smooth, dry brush.
The motor is of the ‘brushless’ type and requires no maintenance.
5.1 Cleaning
When cleaning the bike, use a sponge and/or a soft brush. For the battery-case, a damp cloth
suffices. Use little water. Keep water away from the electrical connections.
Notice: Do not use a jet-wash. The powerful water-jet may damage the electronics.
5.2 Removal and refitting of wheels for bikes with a rear wheel motor
Removal and refitting of the rear wheel is best left to your dealer. If you are forced to do it yourself,
follow the instructions.
• Removal of the rear wheel
1. Make sure that the system is switched ‘Off’.
2. Change to the highest gear.
3. Remove the battery from its docking station.
4. Unplug the connectors of the motor at the left hand
side of the hub. Make sure that both cables are
unplugged. (see photo)
5. Disconnect the rear brake:
-V-brakes, Magura brakes: release the rear brake
- Rollerbrakes: unhook the cable and housing stop from
the brake. Undo the reaction arm bolt
6. Loosen and remove the axle nuts.
Maintenance
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trek RIDE plus EASY II Controller at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trek RIDE plus EASY II Controller in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 9,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info