Manual Trek Incite 11i - 2005 (page 3 of 10) (English)

775420

Zoom out

Zoom in

1/10

INSTALLATION

Tools needed:

• Electrical tape

• Slot-type screwdriver

• Phillips-type screwdriver

• Scissors

This section explains the steps to install your computer onto your bicycle:

• Placing the computer on the handlebar

• Placing the magnet and sensor(s) on the bike

Placing the computer on the handlebar

The Trek Incite computer can be mounted on the handlebar or on the stem (Figure

3).

To install the computer on the handlebar

1. Determine your bicycle’s handlebar diameter: 22.2mm, 25.4/26.0mm, or 31.8mm.

2. Select the corresponding bar clamp

For a 22.2mm bar, use the rubber shim (provided) inside the smaller clamp.

3. Insert the handlebar clamp into the back of the computer base (Figure 4) and

slide it towards the front of the base.

4. Insert the rubber friction pad into the computer base, aligned across the

computer base.

5. With the wire pointing toward the front of the bike, wrap the bar clamp around

the handlebar.

6. Insert the screw through the washer and into the computer base.

7. Tighten the screw until the computer base cannot rotate on the handlebar.

8. Slide the computer into the computer base until the front of the computer and

computer base line up.

9. Check that the computer base cannot be rotated around the handlebar, and that

the computer cannot slide backwards on the computer base (Figure 5).

To install the computer on the stem

1. Insert the rubber friction pad into the computer base, aligned along the

computer base.

2. Insert two nylon ties through the computer base (Figure 6).

3. Place the base on the stem and tighten the nylon tie.

4. Slide the computer into the computer base until the front of the computer and

computer base line up.

5. Check that the computer base cannot be rotated around the stem and the

computer cannot slide backwards on the computer base.

6. Tighten the nylon ties and trim the excess length.

Placing the magnet and sensor(s) on the bike

The wheel magnet must be aligned so that it passes across the sensor. As the

magnet passes the sensor, it must be no further from the sensor than 1 to 3mm (1/

32 to 1/8 inch).

The wheel magnet has a ‘T’ shaped slot with two configurations: round spokes and

flat or bladed spokes (Figure 7).

Computers with the cadence function have two sensors. The shorter computer

wire is for the cadence sensor which mounts near the crankset. The sensor must be

aligned so that the magnet passes within 1-3mm of the sensor, and in line with

the small line on the sensor (Figure 8).

To install the magnet

1. Remove the screw from the magnet.

2. Slide the slot in the back of the magnet over the spoke.

For a flat or bladed spoke, start the spoke near the end where the spoke is round, and align the

top of the ʻTʼ with the spoke as you slide the magnet up the blade.

3. Thread the screw into the magnet until it is snug against the spoke.

Installation

Figure 6- Nylon tie

threaded through com-

puter base

Figure 7- Magnet placed

on round and oval

spokes

Figure 3- Computer on

handlebar and stem

Figure 4- Clamp and

friction pad in computer

base

Figure 5- Make sure the

computer cannot be

bounced off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Trek Incite 11i - 2005 in the language / languages: English as an attachment in your email.

The manual is 0.4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Trek Incite 11i - 2005 Manual

Product: