798760

Traeger Texas Pro - BBQ075.02 Manual

8
Zoom out
Zoom in
Previous page
1/24
Next page
SECTION TWO: INITIAL FIRING INSTRUCTIONS
(To be used on initial firing or anytime the Grill runs out of Pellets)
In order to ensure proper operation of the Grill, you must first
allow the Auger Tube to be “charged” with Pellets.
1) Open the Door and remove the Porcelain Grill, Grease Drain Pan and Heat Baffle
from inside the Grill.
2) Make sure the Switch is in the OFF (o) position. Plug the Power Cord into an
appropriate, grounded electrical outlet.
3) Open the Pellet Hopper Lid and locate the Auger. Make sure there are no foreign
objects in the Auger. Turn the Switch ON (--) and the Temperature/dial to smoke
look into the Pellet Hopper to confirm the Auger is turning. At the same time, place
your fingers over the Firepot and feel the air movement from the Draft Inducer Fan.
Look to see if the Hot Rod is getting hot (it will start to turn red). CAUTION! Do not
touch it. Turn the Temperature/dial to SHUT DOWN CYCLE.
4) Fill the Pellet Hopper with TRAEGER BBQ PELLETS. WARNING! Use only
TRAEGER BRAND BBQ PELLETS, which are specifically made to work in our
Grills. Never use heating fuel pellets in the Grill. Turn the Temperature/Dial to
HIGH. Note: During the initial charging of the Auger, it will take time for the Pellets to
travel from the Pellet Hopper to the Firepot. When the Pellets begin to fall into the
Firepot, turn the Temperature/Dial to Shut Down Cycle.
5) Set the Temperature/Dial to SMOKE. Let the Pellets come to full flame. Once you
see flames come out of the Firepot, turn the Temperature/Dial to SHUT DOWN
CYCLE, and let the Grill cool down.
Recommendation: For ease of clean-up, line the Grease Drain Pan with heavy-
duty aluminum foil. Be sure the edges and ends of the foil are tight against the
bottom of the Grease Drain Pan. Position the Heat Baffle, The foil lined Grease
Drain Pan and Porcelain Grill in their proper locations.
6) With the Door open set the Temperature/Dial to SMOKE. In approximately 2 minutes
you will notice whitish-gray smoke coming out of the Grill as the Pellets ignite. After
assuring the Pellets have ignited, close the Door and set the Temperature/Dial to
any cooking setting desired.
7) Note: Before cooking the first batch of food in your new Grill, you will need to
season the Grill. Turn the Temperature/Dial to HIGH and run for 45 minutes at
this setting with the Door closed. This must be done before cooking any food
on the Grill.
8) The Grill should be allowed to preheat for approximately 10 minutes with the Door
closed before placing food in the grill.
WARNING! START THE GRILL ON SMOKE SETTING
WITH THE DOOR OPEN
Once the Pellets are ignited, close the Door and
set the Temperature Dial to any cooking temperature desired.
WARNING! When operating this Grill, maintain a minimum
clearance of 12 inches from Grill to combustibles
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Traeger Texas Pro - BBQ075.02 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Traeger Texas Pro - BBQ075.02 in the language / languages: English as an attachment in your email.

The manual is 1.16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info