798692

Traeger Silverton - TFS62PLD Manual

22
Zoom out
Zoom in
Previous page
1/28
Next page
22
Question Answer
Why won’t
my grill
ignite?
Verify power at the
electrical outlet.
If the power cord is connected to a GFCI (ground fault circuit
interrupter), check and reset if necessary.
Initiate start-up. If ignition does not occur, proceed to next answer.
DANGER! Turn the
switch OFF (O) and
disconnect the power
cord.
Remove the control and check the fuse on back. Replace the fuse if
blown. Reinstall the control.
Check the draft inducer fan and the auger drive motor for operation. If both are operating, then
the hot rod needs to be replaced. If one or both are not operating, contact Traeger's VIP-365
Customer Service (see page 26) for additional troubleshooting help or to place an order.
Why are no
pellets being
delivered
into the
repot?
Verify that there are pellets in the pellet hopper. If this is the initial ring or the grill has run
out of pellets, allow sufcient time for the pellets to travel from the pellet hopper to the repot
(can take up to 7 minutes).
Initiate start-up.
See the “Initial Firing
Instructions” section
on page 10.
If there are still no pellets in the repot, proceed to next answer.
If the auger drive motor is operating (check the small fan blade on the back of the motor),
then the problem is in the digital control, which will need to be replaced. Contact your
Traeger dealer or Traeger's VIP-365 Customer Service (see page 26) to place an order.
If the auger drive
motor is not
operating but the
draft inducer fan
is operating, then
the problem is in
the auger system,
which will need to be
checked.
With the switch OFF (O), locate the small fan blade on the back of the
auger drive motor.
CAUTION! While watching the fan blade, turn the switch ON (I). If
the fan blade does not turn, turn the switch OFF (O). This indicates
a defective auger drive motor, and it will need to be replaced. Contact
your Traeger dealer or Traeger's VIP-365 Customer Service (see page
26) to place an order.
If the fan blade turns a bit and then stops, continue watching and
turn the switch OFF (O). If the fan blade unwinds slightly, this
indicates a jam in the auger system which will need to be cleared.
DANGER! Turn the switch OFF (O) and disconnect the power cord.
Remove the pellets from the pellet hopper. Check for foreign objects
and wet or decomposed pellets, both of which can cause a jam in the
auger system. The auger will need to be removed to clear a jam in the
auger system. See “How do I remove the auger if it jams?”
How do I
remove the
auger if it
jams?
DANGER! Turn the switch OFF (O) and disconnect the power cord.
CAUTION! If the grill is still hot, allow it to cool thoroughly.
Remove any covers necessary to access the auger drive motor.
Remove the screw connecting the auger drive motor shaft to the auger shaft and the screw
retaining the auger bushing into the auger tube.
With a small pipe wrench or locking pliers on the auger shaft, turn the auger
counterclockwise. It will turn hard until it breaks free; then the auger will turn freely.
Remove the auger and clean all pellets, ash, or foreign objects from the auger, auger tube,
and repot. (See instructions for proper handling and disposal of ash on page 21.)
Sand the outside surfaces of the auger with medium grit sandpaper. Check the inside of the
auger tube and sand it if needed. Vacuum the sanding grit out of the auger tube and repot
when nished. Check that the auger rotates freely.
Reattach the auger shaft to the auger drive motor shaft.
FREQUENTLY ASKED QUESTIONS
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Traeger Silverton - TFS62PLD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Traeger Silverton - TFS62PLD in the language / languages: English as an attachment in your email.

The manual is 8.67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info