798691

Traeger Select Pro Bronze - BBQ400.02 Manual

13
Zoom out
Zoom in
Previous page
1/18
Next page
4) If the Auger Drive Motor is not operating but the Draft Inducer Fan is operating, the
problem is in the Auger system, which will need to be checked.
a) With the Power Switch and the Switch/Dial OFF, locate the small fan blade
on the back of the Auger Drive Motor.
b) While watching the fan blade, turn the Power Switch and then the Switch/Dial to
ON. If the fan blade does not turn, turn the Switch/Dial to OFF. This indicates a
defective Auger Drive Motor and it will need to be replaced. Contact your
Traeger Dealer or the Traeger Parts Department (SECTION SEVEN) to place
an order.
c) If the fan blade turns a bit and then stops, continue watching and turn the
Switch/Dial to OFF. If the fan blade UNWINDS slightly, this indicates a jam in
the Auger system which will need to be cleared.
d) Disconnect Power Cord from electrical outlet and remove Pellets from the Pellet
Hopper. Check for foreign objects and wet/decomposed Pellets, both of which
can cause a jam in the Auger system. The Auger will need to be removed to
clear a jam in the Auger system. See “HOW DO I REMOVE THE AUGER IF IT
JAMS?” section below.
`
HOW DO I REMOVE THE AUGER IF IT JAMS?
1) Remove any covers necessary to access the Auger Drive Motor.
2) Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft and
the screw retaining the Auger Bushing into the Auger Tube.
3) With a small pipe wrench or locking pliers on the Auger shaft, turn the Auger counter
clockwise. It will turn hard until it breaks free, then the Auger will turn freely.
4) Remove the Auger and clean all Pellets, ash or foreign objects from the Auger,
Auger Tube and Firepot. A shop-vac is ideal for this task.
5) Sand the outside surfaces of the auger with medium grit sandpaper. Check the
inside of the Auger Tube and sand it if needed. Vacuum the sanding grit out of the
Auger Tube and Firepot when finished.
6) Reinstall the Auger Bushing and the Auger into the Auger Tube, making sure that
the Auger rotates freely.
7) Re-attach the Auger shaft to the Auger Drive Motor shaft.
WHY DOES MY GRILL FIRE GO OUT ON “SMOKE” SETTING?
Excess ash in the Firepot may be the problem.
1) Open the Door/Lid and remove the Porcelain Grill, Grease Drain Pan and Heat
Baffle from inside the Grill.
2) IMPORTANT: Remove all unburned Pellets and ash from inside and around
the Firepot. A shop-vac is ideal for this task CAUTION! ASSURE THAT THE
GRILL IS COLD TO AVOID A FIRE FROM HOT ASH.
3) Replace the Heat Baffle, Grease Drain Pan and the Porcelain Grill and initiate start-
up procedure.
4) If this didn’t remedy the problem, contact Traeger Technical Support (SECTION
SEVEN) for additional troubleshooting help.
WITH THE TRAEGER DIGITAL CONTROL, WHAT DIAL SETTING IS
RECOMMENDED FOR STARTING THE GRILL?
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Traeger Select Pro Bronze - BBQ400.02 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Traeger Select Pro Bronze - BBQ400.02 in the language / languages: English as an attachment in your email.

The manual is 1.04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info