798678
22
Zoom out
Zoom in
Previous page
1/32
Next page
22
Question Answer
Why won’t
my grill
ignite?
Verify power at the
electrical outlet.
If the power cord is connected to a GFCI (ground fault circuit
interrupter), check and reset if necessary.
Initiate start-up. If no ignition, see next answer.
DANGER! Turn the switch
OFF (O) and disconnect
the power cord.
Remove the control and check the fuse on back. Replace the fuse
if blown. REINSTALL THE CONTROL.
Check the draft inducer fan and the auger drive motor for operation. If both are operating,
the hot rod needs to be replaced. If one or both are not operating, contact Traeger's VIP-365
Customer Service (see page 27) for additional troubleshooting help or to place an order.
Why are no
pellets being
delivered
into the
repot?
Verify that there are pellets in the pellet hopper. If this is the initial ring or the grill has run
out of pellets, allow sufcient time for the pellets to travel from the pellet hopper to the repot
(can take up to 7 minutes).
Initiate start-up.
See “INITIAL FIRING
INSTRUCTONS” on
page 10.
If there are still no pellets in the repot, proceed to next answer.
If the auger drive motor is operating (check the small fan blade on the back of the motor), the
problem is in the digital control, which will need to be replaced. Contact your Traeger dealer
or Traeger's VIP-365 Customer Service (see page 24) to place an order.
If the auger drive motor
is not operating but
the draft inducer fan is
operating, the problem is
in the auger system, which
will need to be checked.
With the switch OFF (O), locate the small fan blade on the back
of the auger drive motor.
CAUTION! While watching the fan blade, turn the switch ON
(I). If the fan blade does not turn, turn the switch OFF (O). This
indicates a defective auger drive motor, and it will need to be
replaced. Contact your Traeger dealer or Traeger's VIP-365
Customer Service (see page 27) to place an order.
If the fan blade turns a bit and then stops, continue watching
and turn the switch OFF (O). If the fan blade UNWINDS slightly,
this indicates a jam in the auger system which will need to be
cleared.
DANGER! Turn the switch OFF (O) and disconnect the power
cord. Remove the pellets from the pellet hopper. Check for foreign
objects and wet or decomposed pellets, both of which can cause
a jam in the auger system. The auger will need to be removed to
clear a jam in the auger system. See “How do I remove the auger
if it jams?” section on page 23.
FREQUENTLY ASKED QUESTIONS
66103_PRO15_v10.indd 22 11/12/15 11:30 AM
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Traeger Pro 22 - Gen 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Traeger Pro 22 - Gen 1 in the language / languages: English as an attachment in your email.

The manual is 6.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Traeger Pro 22 - Gen 1

Traeger Pro 22 - Gen 1 User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info