650608
10
Zoom out
Zoom in
Previous page
1/20
Next page
3. CHECK THE WICK LIFE EXTENDER
On your first use of new heater or after replacing the wick, check if the WICK
LIFE EXTENDER if it on position 1. If not, relocate the WICK LIFE EXTENDER to
position 1 by following the instructions on page 9, ADJUSTMENT OF WICK
HEIGHT WITH WICK LIFE EXTENDER.
4. ENGAGE THE AUTOMATIC EXTINGUISHER
The automatic extinguisher is engaged automatically by turning the wick
adjuster knob clockwise. Check the operation of the automatic extinguisher
before lighting your heater. After turning the wick adjuster knob clockwise until
it stops, turn the manual shutoff counterclockwise to be sure the wick moves
smoothly down.
LIGHTING
NOTE: When you first use your new heater, ignite it out of the living area of your house, either in a garage
or an outside area protected from strong drafts. Burn it for about 15 minutes to remove all of the
protective oil present on the burner parts. lf this 15 minutes ”burn-in” is done inside, some
objectionable odor will be observed. This procedure is necessary ONLY THE FIRST TIME you ignite
your heater.
NOTE: lf you have fueled your heater for the first time, or if you are refueling it
after it has been out of fuel for a long time, you will need to wait about
thirty (30) minutes for the wick to become fully saturated before Iighting.
Failure to allow enough time for the wick to become fully saturated may
cause permanent damage to the wick when it is lighted.
1. Turn the wick adjuster knob clockwise until it stops. This raises the wick to its
maximum height. As the wick rises within the heater, the wick adjuster knob
turns with some resistance and makes a sound like the winding of a clock.
Once the wick has reached its proper height, the automatic extinguisher is fully
engaged. The wick adjuster knob will now move freely left or right to adjust
the flame.
2. AUTOMATIC LIGHTNG
Gently push down the igniter lever. The igniter coil should glow and touch the
wick. When flame appears, release the igniter lever.
NOTE: If you have diffculty igniter wick, let up on the igniter lever very slightly
to remove the igniter coil from direct contact with the wick.
3. LIGHTING WITH A MATCH
Tilt the heat chamber and touch the match to the top of the wick. Do not allow
burned parts of the match to fall or remain on the wick.
4. Be sure that heat chamber is properly seated by moving the wire heat chamber
handle left and right.
NOTE: An improperly seated heat chamber can cause high flame, smoke, and
potential damage to the heater itself. Proper seating of the heat chamber
is essential for good performance. Do not leave the heater until you have
determined that the flame is burning normally, as described in the
following section.
8
KS-47B_US.qxd 14.7.25 13:18 ページ 8
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toyotomi KS-47B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toyotomi KS-47B in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info