458422
31
Zoom out
Zoom in
Previous page
1/77
Next page
19
English Français
Straight stitching
Starting to sew (fig A)
3. Raise the needle to its highest position, and lift
the presser foot lever.
4. Place fabric under the presser foot. Lower
presser foot.
5. Press the foot controller lightly and sew forward,
guiding the fabric by hand as it is fed. Do not
push or pull the material.
Turn a square corner (fig B)
To change sewing direction.
1. Stop the machine at the point you want to
change sewing directions, with the needle in the
fabric.
2. Raise the presser foot, turn the fabric to its new
direction.
3. Lower the presser foot and begin sewing in the
new direction.
Reverse sewing (fig C)
To reinforce seam, it is recommended to start or
end with a few stitches in reverse sewing.
Push the reverse lever to sew reverse. Guide the
fabric as it is fed. Do not pull the material.
For reinforcment, a few stitches are enough.
Release lever to return to forward sewing.
Finishing sewing (fig D)
1. Stop pressing the foot controller. Turn the
handwheel until the needle is at its highest
position. Raise presser foot.
2. Draw out the fabric to the left. (fig D-1)
3. Cut threads with the cutter. (fig D-2)
4. Leave 15 cm of thread clear behind to prevent
the thread from drawing out of the needle eye.
(fig D-3)
Points droits
Commencer à coudre (fig. A)
3. Lever laiguille à sa position la plus haute, et
lever le levier presseur de pied-de-biche.
4. Placer le tissu sous le pied-de-biche. Abaisser
le pied-de-biche.
5. Presser doucement sur la pédale et coudre en
avant, en guidant le tissu avec les mains pour
alimenter la machine. Evitez de pousser ou de
tirer le tissu.
Changement de direction de couture (fig. B)
Coudre en changeant de directions.
1. Arrêter la machine au point où vous voulez
changer de direction, avec laiguille dans le
tissu.
2. Levez le pied-de-biche, tourner le tissu vers sa
nouvelle direction.
3. Abaissez le pied-de-biche et commencez à
coudre dans la nouvelle direction.
Coudre en marche arrière (fig. C)
Pour renforcer la couture, il est recommandé de
commencer ou de terminer avec quelques points
cousus en marche arrière.
Pousser le levier de marche arrière pour coudre
en marche arrière. Guider le tissu lorsquil
alimente la machine. Eviter de tirer sur le tissu.
Pour renforcer une couture, plusieurs points sont
nécessaires.
Relâcher le levier de marche arrière pour revenir
au mode de couture vers lavant.
Pour terminer la couture (fig. D)
1. Arrêter de presser la pédale. Tournez le volant
jusqu’à ce que laiguille se retrouve à sa
position la plus haute. Lever le pied-de-biche.
2. Retirer le tissu par la gauche. (fig. D-1)
3. Couper les fils avec le coupe-fil. (fig. D-2)
4. Laisser 15 cm de fil libre derrière afin de
lempêcher de sortir du chas de laiguille. (fig. D-3)
A B
p1-end 05.1.11 0:51 PM ページ 19
31


Need help? Post your question in this forum.

Forumrules
1

Forum

toyota-quilt50

Reset search

  • I have posted a complaint which has been rejected because of spam - clever! Submitted on 13-2-2020 at 11:22

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toyota Quilt50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toyota Quilt50 in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toyota Quilt50

Toyota Quilt50 User Manual - German - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info