458421
56
Zoom out
Zoom in
Previous page
1/79
Next page
45
English Français
Nederlands Italiano
ABC
DE FG
Piecing Foot
Use the 1/4” piecing foot whenever a 1/4” seam allowance is
required.
A. Raise the foot release lever to remove the foot.
B. Place the piecing foot on the needle plate aligning needle
holes.
C.
Lower the presser foot lever so that the ankle snaps on the foot.
To stitch a 1/4” seam:
D. Align the edges of the fabrics with the right edge of the
presser foot.
E. When pivoting at a corner, stop when the fabric edge is
even with the front red line on the foot. Lower the needle
into the fabric and pivot. Continue to stitch.
To stitch a 1/8” seam:
F. Align the edges of the fabrics with the inside edge of the
right side of the presser foot.
G. When pivoting at a corner, stop when the fabric edge is
even with the middle red line on the foot. Lower the
needle into the fabric and pivot. Continue to stitch.
Always use straight stitch (center position).
Piecing Foot is an optional accessory.
Verstelvoet
Gebruik de 6mm verstelvoet wanneer U een 6mm naadomslag wilt.
A. Zet de persvoethendel omhoog zodat U het voetje kan
verwijderen.
B. Plaats de verstelvoet op de naaldplaat zodat de
naaldopening gelijk valt met die van de naaldplaat.
C. Zet de persvoethendel naar beneden zodat het pinnetje in de
houder klikt.
Het naaien van 6 mm naad:
D. Plaats de kant van de stof gelijk aan de rechterkant van de
persvoet.
E. Wanneer U op een hoek wilt draaien, stop dan wanneer de
zijkant van de stof gelijk ligt met de voorste rode lijn op het
voetje. Plaats de naald in de stof en draai de stof. Ga verder
met naaien.
Het naaien van 3 mm naad:
F. Plaats de kant van de stof gelijk aan de rechterbinnenkant
van de persvoet.
G.
Wanneer U een hoek wilt draaien, stop dan wanneer de zijkant van
de Stof gelijk ligt met de middelste rode lijn op het voetje. Plaats de
naald in de stof en draai de stof. Ga verder met naaien.
Gebruik altijd de rechte steek (middelste stand).
Verstelvoet is een optioneel accessoire.
Piedino per patchwork
Usate il piedino per patchwork da 6 mm quando avete
bisogno di questo tipo di cucitura.
A. Alzate la leva alza piedino per togliere il piedino.
B. Mettete il piedino per patchwork sulla placca ago
allineando i buchi dell’ago.
C. Abbassate la leva alza piedino cosicché il piedino si
agganci da solo.
Per cuciture da 6 mm di larghezza
D. Allineate i bordi del tessuto con il lato destro del piedino.
E. Quando girate un angolo, fermatevi quando il bordo del
tessuto è pari con la linea rossa frontale del piedino.
Abbassate l’ago nel tessuto e girate. Continuate a cucire.
Per cuciture di 3 mm di larghezza
F. Allineate i bordi del tessuto con il bordo interno del lato
destro del piedino.
G. Quando girate un angolo, fermatevi quando il bordo del
tessuto è pari con la linea rossa media del piedino.
Abbassate l’ago nel tessuto e girate. Continuate a cucire.
Utilizzare sempre il punto diritto (posizione centrale).
Il piedino per patchwork è un accessorio opzionale.
Pied d’application
Utilisez le pied quart de pouce toutes les fois ou une couture
quart de pouce est requise.
A. Poussez le levier de changement de pied-de-biche vers vous
et retirez le pied en place.
B. Mettre en place le pied d’application sur la plaque aiguille puis
alignez les trous de la plaque avec celui du pied d’application.
C. Abaissez le levier de pied-de-biche de manière à clipper le
pied sur son support.
Pour coudre une couture quart de pouce:
D. Alignez les bords du tissu avec le bord droit du pied-de-biche.
E. Lorsque vous parvenez au bord du tissu, stopper la couture
en prenant soin de vérifier que le bord du tissu soit en face de
la première ligne rouge du pied-de-biche. Piquez l’aiguille
dans le tissu, relevez le levier de pied-de-biche comme en C.
et tournez le tissu de 90
o
, vous pouvez alors poursuive la
couture en point droit et répéter l’opération à chaque angle.
Pour coudre une couture huitième de pouce:
F.
Alignez les bords du tissu avec le bord intérieur droit du pied-de-biche.
G. Pour négocier le passage des angles, lorsque vous arrivez au
bord du tissu, stopper la couture en alignant les bords du tissu
avec la 2
ème
ligne rouge (milieu) du pied-de-biche. Tout en
laissant l’aiguille plantée dans le tissu, faire pivoter l’ouvrage
et continuez ainsi à coudre.
Toujours utiliser le point droit (position centrale).
Le pied d'application est un accessoire en option.
RS2000-2D_EFNI.book Page 45 Wednesday, July 27, 2005 7:39 AM
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toyota JetB224 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toyota JetB224 in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 4,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toyota JetB224

Toyota JetB224 User Manual - English - 81 pages

Toyota JetB224 User Manual - German - 48 pages

Toyota JetB224 User Manual - Dutch, French, Italian - 81 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info