458396
61
Zoom out
Zoom in
Previous page
1/115
Next page
Español
English
Français
46
SEWING
STRAIGHT STITCH
Warning:
Always use proper presser foot for the stitch pattern.
A. Attach the zigzag foot.
B. Set stitch width at "0".
When the stitch width is not set at "0", the stitch will
form zigzag.
C. Turn the pattern selection dial and select straight
stitch (Stitch No.2).
D. Set stitch length between "1" and "4".
E. Set thread tension dial at "4".
• Insert fabric under the foot. Lower the needle by
pressing the needle up and down button.
• Lower the presser foot lifter.
• Press the start and stop button and start sewing.
When using the foot controller, step on the foot
controller to start the machine.
The first 2 or 3 stiches will start very slowly.
Removing the fabric
F. Press the start and stop button and stop the
machine.
When using the foot controller, release the foot
controller.
G. Raise the presser foot lifter and gently pull the fabric
to the left.
H. Cut excess thread with the thread cutter.
COSTURA
Punto recto
ADVERTENCIA
Utilice siempre un prensatelas adecuado al tipo de
punto.
A.Coloque un prensatelas para costuras en zigzag.
Prensatelas para costuras en zigzag
B.Coloque el selector de anchura de puntada en la
posición "0".
Cuando el selector de anchura de puntada se
encuentra en otra posición que el "0", la máquina
cose en zigzag.
C.Gire el selector de punto para seleccionar el punto
recto (n°2).
D.Coloque el selector de longitud de puntada entre el
"1" y el "4".
E.Coloque el selector de tensión del hilo en la posición
"4".
• Coloque la tela debajo del prensatelas. Baje la aguja
con el botón de subida y bajada de la aguja.
• Baje la palanca del prensatelas.
• Pulse el botón de arranque y parada, y empiece a
coser.
Si utiliza el mando de pedal, píselo para arrancar la
máquina.
Las 2 ó 3 primeras puntadas se hacen muy despacio.
Para sacar la tela
F.Pulse el botón de arranque y parada para parar la
máquina.
Si utiliza el mando de pedal, levante el pie.
G.Levante la palanca del prensatelas y retire
cuidadosamente la tela hacia la izquierda.
H.Corte el hilo que sobre con la cuchilla.
COUTURE
Point droit
AVERTISSEMENT
Utilisez toujours un pied-de-biche adapté au type de
point.
A.Fixez le pied-de-biche pour zigzag
Pied-de-biche pour zigzag
B.Sélectionnez la largeur de point "0".
Lorsque le sélecteur de largeur de point se trouve
sur une position autre que "0", la machine coud en
zigzag.
C.Tournez la molette de sélection du point pour
sélectionner le point droit (point n°2).
D.Sélectionnez une longueur de point entre "1" et "4".
E.Placez la molette de réglage de la tension du fil sur
"4".
• Placez le tissu sous le pied-de-biche. Abaissez
l'aiguille en appuyant sur la touche pour relever et
abaisser l'aiguille.
• Baissez le levier du pied-de-biche.
Appuyez sur la touche marche/arrêt et commencez à
coudre.
Si vous utilisez la pédale, appuyez dessus avec le
pied pour mettre la machine en marche.
Les 2 ou premiers points se feront très lentement.
Sortir le tissu
F.Appuyez sur la touche marche/arrêt pour arrêter la
machine.
Si vous utilisez la pédale, relâchez la pression.
G.Relevez le levier du pied-de-biche et repoussez
doucement le tissu vers la gauche.
H.Coupez le fil excédentaire avec le coupe-fil.
P37-48 2006.08.04, 09:24Page 11 Adobe PageMaker 6.5C/PPC
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toyota Ezone at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toyota Ezone in the language / languages: English, German, Dutch, French, Italian, Spanish, Spanish as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info