458417
39
Zoom out
Zoom in
Previous page
1/115
Next page
Nederlands
Deutsch
Italiano
24
EINRICHTEN DER MASCHINE
Spulen
A.Setzen Sie eine Garnspule und eine Spulenkappe
auf den Garnrollenhalter.
Lassen Sie einen Spielraum von 2mm zwischen der
Garnspule und der Spulenkappe.
• Für eine kleine Garnspule
• Für eine große Garnspule
B.Ziehen Sie einen Faden durch Fadenführung und
Spulenfadenführung .
Fadenführung
Spulenfadenführung
C.Führen Sie wie gezeigt das Fadenende durch die
Spulenöffnung.
• Setzen Sie die Spule auf den Spulapparat, damit die
Aussparung auf die Spindelfeder trifft. Drücken Sie
die Spule nach unten und der Spulapparat bewegt
sich automatisch nach rechts.
• ( ) erscheint auf dem Informationsdisplay.
D. Drücken Sie die Geschwindigkeitseinstelltaste nach
rechts, um das Spulen zu beschleunigen.
WARNHINWEISE
Kommen Sie beim Spulen nicht mit dem Spulapparat in
Berührung.
E.Halten Sie das Fadenende.
Drücken Sie die Start-/Stopptaste und starten die
Maschine.
Wenn mit dem Pedal gearbeitet wird, das Pedal zum
Starten der Maschine drücken.
F.Nachdem etwas gespult wurde, die Maschine
anhalten und den überstehenden Faden über der
Spulenöffnung abschneiden und fortfahren
G. • Die Spule hält an, wenn sie gefüllt ist.
• Drücken Sie die Start-/Stopptaste und halten die
Maschine an.
Geben Sie das Pedal frei, wenn Sie mit dem Pedal
arbeiten.
H.Drücken Sie den Spulapparat mit den Fingern nach
links hinten.
Sie können nicht nähen, wenn der Spulapparat nach
rechts gerichtet ist.
I. • Nehmen Sie die Spule von der Spindel.
• Schneiden Sie den Faden durch.
MACHINE KLAARMAKEN VOOR GEBRUIK
Opwinden van de spoel
A. Plaats een spoel met garen en de garengeleider op
de klospen.
Laat ongeveer 2 mm ruimte tussen de spoel en het
spoelklepje.
• Voor een kleine spoel
• Voor een grote spoel
B.Haal de draad door de draadgeleider en door de
spoeldraadgeleider .
Draadgeleider
Spoeldraadgeleider
C.Steek het uiteinde van de draad door het gaatje van
de spoel (zie tekening).
• Plaats de spoel op de as zodat de groef samenvalt
met de veer van de as. Duw de spoel naar beneden
en de spoelwinderas zal automatisch naar rechts
verschuiven.
Op het naai-informatiescherm wordt ( ) weergegeven.
D.Schuif de snelheidsregelaar naar rechts om de spoel
sneller op te winden.
OPGELET
Raak de as tijdens het opwinden van de spoel niet aan.
E.Houd het uiteinde van de draad vast.
Druk op de start-/stopknop om de machine starten.
Als u het bedieningspedaal gebruikt, duw dan het
pedaal in om de machine te starten.
F.Als een beetje draad opgewonden is, stop dan de
machine, knip het extra stukje draad boven het gaatje
in de spoel af en ga verder met het opwinden van de
spoel.
G. • De spoel stopt zodra hij volledig opgewonden is.
• Druk op de start-/stopknop om de machine uit te
schakelen.
Als u het bedieningspedaal gebruikt, laat het
pedaal dan los.
H.Druk de spoelwinderas opnieuw naar links met uw
vinger.
U kunt niet naaien wanneer de spoelwinder zich
rechts bevindt.
I. • Neem de spoel van de as.
• Snij de draad door.
PREPARAZIONE DELLA MACCHINA DA CUCIRE
Avvolgimento della spolina
A. Inserire una spoletta di filo e il relativo cappello sul
perno portarocchetto.
Lasciare un'apertura di 2 mm tra la spoletta e il
relativo cappello.
• Per spoletta di filo piccola
• Per spoletta di filo grande
B.Far passare il filo attraverso il guidafilo , e il guidafilo
della spolina.
Guidafilo
Guidafilo della spolina
C.Far passare il capo del filo nel foro della spolina,
come illustrato.
• Posizionare la spolina sull'albero avvolgitore della
spolina, in modo che la scanalatura vada a
combaciare con la molla dell'albero. Spingere la
spolina verso il basso: l'albero avvolgitore si sposterà
automaticamente verso destra.
• Sul display a cristalli liquidi apparirà il simbolo ( ).
D.Per aumentare la velocità di avvolgimento della
spolina, fare scorrere verso destra la manopola di
controllo della velocità di cucitura.
ATTENZIONE
Non toccare l'albero avvolgitore della spolina durante
l'operazione di avvolgimento di quest'ultima.
E.Tenere il capo del filo con le dita.
Premere il pulsante di avvio e arresto, per avviare la
macchina.
Se si usa il comando a pedale, premerlo per avviare
la macchina.
F.Dopo avere avvolto un po' di filo, arrestare la
macchina e tagliare il filo in più al di sopra del foro
della spolina, e continuare.
G. • Quando si sarà avvolta completamente, la spolina
si arresta.
• Premere il pulsante di avvio e arresto, per arrestare
la macchina.
Se si usa il comando a pedale, togliere il piede da
quest'ultimo.
H.Con il dito, spingere nuovamente verso sinistra
l'albero avvolgitore della spolina.
Quando l'albero avvolgitore della spolina è
posizionato sulla destra, non è possibile cucire.
I. • Togliere la spolina dall'albero.
• Tagliare il filo.
P13-24 2006.08.04, 09:25Page 13 Adobe PageMaker 6.5C/PPC
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toyota EZ901 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toyota EZ901 in the language / languages: English, German, Dutch, French, Italian, Spanish, Spanish as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toyota EZ901

Toyota EZ901 User Manual - English, German, Dutch, French, Italian, Spanish - 115 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info