603758

Toyota DFL Superior 2D Manual

60
Zoom out
Zoom in
Previous page
1/84
Next page
49
English Français
0.3 cm (1/8”)
L
d
t
m
a
b
0.4-1
12
BA
C
Making buttonhole
1. Be sure that the declutch knob in the handwheel is
in the ( ) direction.
2. Measure the diameter and thickness of the button.
Add the thickness and 0.3 cm (for bar tacks) to
diameter. Mark the size of the buttonhole on the
fabric. (fig A)
For stretch fabrics, lay a piece of paper where
the buttonhole will be placed.
3. Attach the Buttonhole Foot. Completely push back
the sliding part a of buttonhole foot. Place material
under the foot so that the marking of buttonhole
passed through the center of foot. (fig B)
4. STEP 1 (front bar tack) (fig C)
Set pattern selection dial to No. 12
Set stitch length dial between 0.4-1
Lower the presser foot and sew 5-6 stitches. Stop
the machine so the needle is at the left side of the
stitches. Raise needle.
5.
STEP 2
(left side) (fig
D
)
Set pattern selection dial to No. 13
Sew left side from front to back until it reaches the end
of the marking. Stop the machine so the needle is at
the left side of the stitches. Raise needle.
6. STEP 3 (back bar tack) (fig E)
Set pattern selection dial to No. 14
Sew 5-6 stitches. Stop the machine so the needle
is at the right side of the stitches. Raise needle.
7. STEP 4 (right side) (fig F)
Set pattern selection dial to No. 15
Sew right side from back to front until it catches the
front bar tack. Stop the machine so the needle is at
the left side of the stitches. Raise needle and
presser foot.
8. Remove the fabric from the machine. Place a pin
through the bar tacks to prevent over-cutting. Cut
the center of the buttonhole with a
Buttonhole
Cutter. (fig G)
Included in accessories.
Use buttonhole foot
Faire des boutonnières
1. Vérifier que le bouton de débrayage est bien
enclenché vers ( ).
2. Mesurer le diamètre et l’épaisseur du bouton.
Ajouter de l’épaisseur et 0,3 cm (pour le point
d’arrêt) au diamètre.
Marquer la taille de la boutonnière sur le tissu. (fig.
A
)
Pour du stretch, placer un morceau de papier là
où la boutonnière sera placée.
3. Mettre en place le pied-de-biche boutonnière.
Passer à l’arrière la partie lisse
a
du pied-de-biche
boutonnière. Placer le tissu sous le pied-de-biche de
tel sorte que la marque effectué pour la boutonnière
passe par le centre du pied-de-biche. (fig.
B
)
4. ETAPE 1 (point d’arrêt devant) (fig. C)
Régler le cadran sélecteur de point sur n° 12
Régler la longueur de point entre 0,4 - 1
Abaisser le pied-de-biche et coudre 5-6 points.
Arrêter la machine de tel sorte que l’aiguille du côté
gauche des points. Relever l’aiguille.
5. ETAPE 2 (côté gauche) (fig. D)
Régler le cadran sélecteur de point sur n° 13
Coudre d’avant en arrière jusqu’à ce
qu’il atteigne
la fin du marquage. Arrêter la machine avec
l’aiguille à gauche. Relever l’aiguille.
6. ETAPE 3 (point d’arrêt à l’arrière) (fig. E)
Régler le cadran sélecteur de point sur n° 14
Coudre 5 à 6 points. Arrêter la machine avec
l’aiguille à droite des points. Relever l’aiguille.
7. ETAPE 4 (côté gauche) (fig. F)
Régler le cadran sélecteur de point sur n° 15
Coudre le côté droit, de l’arrière a l’avant jusqu’à ce
qu’il rejoigne le point d’arrêt de devant. Arrêter la
machine avec l’aiguille à gauche des points.
Relever l’aiguille et le pied-de-biche.
8. Enlever le tissu de la machine. Placer une épingle
à travers le point d’arrêt pour éviter des erreurs de
découpe. Couper le centre de la boutonnière avec
un coupe boutonnière. (fig. G)
Inclus dans les accessoires.
L
Caution!
When using the buttonhole cutter to cut the buttonholes,
do not hold the fabric in front of the cutter.
Doing so could cause an injury to your hand.
Attention!
Lorsque vous utilisez le couteau à boutonnière pour
ouvrir la boutonnières, ne tenez pas le tissu juste
devant le couteau à boutonnière.
Sinon vous risquez de vous blesser la main.
… 60 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toyota DFL Superior 2D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toyota DFL Superior 2D in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 4,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Toyota DFL Superior 2D

Toyota DFL Superior 2D User Manual - German - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info