465054
13
Zoom out
Zoom in
Previous page
1/40
Next page
13
Connections
Connections
Notes
If Auto is selected, it follows preference HDMI aspect ratio of TV.
Refer to the owner’s manual of the connected TV as well.
When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making
any connections.
If you have a HDMI (with HDCP) equipped monitor or display, you can connect it to this player using a HDMI cable.
The HDMI connector outputs uncompressed digital video, as well as almost every kind of digital audio that the player is compatible
with, including DVD-Video, Video CD/Super VCD, CD, WMA MP3 and DivX
®
.
This unit has been designed to be compliant with HDMI (High Definition Multimedia Interface) depending on the component you
have connected. Using a HDMI connection may result in unreliable signal transfers.
Because HDMI is an evolving technology, it is possible that some devices with an HDMI input may not operate properly with this
DVD player.
When using HDMI cable, do not connect to other analog video outputs.
No sound will be output from the HDMI cable if the digital out is not set to PCM.
HDMI output is only available when the Video Output is set to “HDMI”. Otherwise the HDMI button is invalid.
Notes
DO NOT connect the OPTICAL OUT or COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the AC-3 RF input of a Dolby
Digital Receiver. This input on your A/V Receiver is reserved for Laser disc use only and is incompatible with the OPTICAL OUT
/COAXIAL DIGITAL AUDIO OUT jack of the DVD player.
Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the “DIGITAL (COAXIAL)” input of a Receiver or Processor.
Connect the OPTICAL OUT jack of the DVD player to the “DIGITAL (OPTICAL)” input of a Receiver or Processor.
Refer to the owner’s manual of the connected equipment as well.
When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall
outlet before making any connections.
The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
For connection to your TV, see “Connecting to a TV” .
This section uses the following reference marks.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD player to optional audio equipment.
Warning
When you are connecting (via the OPTICAL OUT or COAXIAL
DIGITAL AUDIO OUT jack) an AV decoder that does not have
Dolby Digital, Digital Theater Systems (DTS) or MPEG2
decoding function, be sure to set “Digital Output” to “PCM”
from the on-screen displays. Otherwise, high volume sound
may damage your hearing as well as the speakers.
• When playing DTS-encoded discs (DVDs and audio CDs),
excessive noise may be output from the analog audio output
jacks. To avoid possible damage to the audio system, you
should take proper precautions when the analog audio output
jacks of the DVD player are connected to an amplification
system. To enjoy DTS Digital Surround™ playback, an external
5.1 channel DTS Digital Surround™ decoder system must be
connected to the OPTICAL OUT or COAXIAL DIGITAL AUDIO
OUT jack of the DVD player.
Content of the output for each output jack is shown in the following
table and differ depending on the On-Screen Display Setting:
"Video Output" HDMI Output HDMI Video Component S-Video
Setting Setting * Output Output Output Output
Component Invalid - Composite 480i -
(Interlaced)
S-VIDEO Invalid - Composite - S-Video
P-Scan Invalid - Composite 480p -
(Progressive)
480p 480p Composite 480i -
HDMI 720p 720p Composite 480i -
1080i 1080i Composite 480i -
1080p 1080p Composite 480i -
1080p/24F 1080p/24F Composite 480i -
* Settings for HDMI output format are performed using the HDMI button
on the remote control.
Content of output for each output jackOn-Screen Display Setting
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba XD-E500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba XD-E500 in the language / languages: English as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info